557409
13
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
5 Installing the boiler
Logano plus GB402 – 6 720 804 428 (2012/09)
13
5 Installing the boiler
5.1 Installation requirements
Preventing noise disturbance for end-users
Where the boiler surroundings are sensitive to noise (e.g. residential
units) the use of flue silencers and flexible pipe work connections may
be considered.
5.2 Recommended wall clearances
When determining the installation location, take the clearances for the
flue and the connection pipe assembly into consideration ( Fig. 7 and
Chapter 6 flue system connection and the pipework on the water and
gas sides, page 13).
Fig. 7 Wall clearances in the installation room
5.3 Heating boiler align
Level the boiler horizontally to prevent air pockets forming inside the
boiler and to enable condensate to drain fully from the condensate pan.
Bring the boiler into its final position.
Level the boiler horizontally by means of its adjustable feet and a spirit
level.
Fig. 8 Levelling the boiler
6 Fitting
6.1 Making the flue gas connection
Observe all country-specific requirements when installing the flue
system.
NOTICE: System damage due to frost!
Site the heating system in a room safe from the risk of
frost.
DANGER: Danger posed by explosive and easily
flammable materials!
Never use or store easily flammable materials (paper,
curtains, clothing, thinners, paints, etc.) in the vicinity
of the boiler.
NOTICE: Risk of boiler damage through contaminated
combustion air.
Never use chlorinated cleaning agents or halogenated
hydrocarbons (as contained in spray cans, solvents,
cleaning agents, paints and adhesives, for example).
Never store or use such materials in the boiler room.
Avoid very dusty atmospheres (building dust).
NOTICE: Boiler damage through overheating.
Excessive ambient temperatures can result in heating
system damage.
Ensure ambient temperatures above 0 °C and below
35 °C.
Where applicable, allow extra wall clearances for
additional components, for example DHW cylinder, pipe
connections or other components on the flue gas side etc.
Dimension Wall clearance (mm)
Minimum recommended
A 700 1000
B 150 400
C
1)
1) This clearance dimension applies independently of the installed flue system.
--
D 700 1000
E
1)
150 400
Tab. 8 Recommended and minimum wall clearances (dimensions in
mm). Maintain minimum clearance, dimension E.
NOTICE: Boiler damage through insufficient load-
bearing capacity of the installation area or unsuitable
substrate!
Ensure that the installation area offers sufficient load-
bearing capacity.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Buderus Logano plus GB402 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Buderus Logano plus GB402

Buderus Logano plus GB402 Bedienungsanleitung - Deutsch - 2 seiten

Buderus Logano plus GB402 Bedienungsanleitung - Englisch - 20 seiten

Buderus Logano plus GB402 Installationsanweisung - Holländisch - 60 seiten

Buderus Logano plus GB402 Bedienungsanleitung - Holländisch - 16 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info