Bedienungsanleitung Bueno Spa Boston (Seite 17 von 40) (Englisch)

784865

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INITIAL INSTALLATION

SITE PREPARATION

When choosing a site for the hot tub take into account that

its maintenance and repair works must be carried out behind

the sidewalls, so accessibility and hot tubce to walk around

the hot tub must be ensured.

1. INDOOR/BASEMENT INSTALLATION

If you place your hot tub indoors, be aware of some special

requirements:

Water may accumulate around the hot tub, so the flooring

material must have a proper runoff to avoid accumulation of

water. When building a new room for the hot tub, construct-

ing a floor drain is required, or damages may occur due to

overflow, overfilling, or technical failure. Our company does

not take responsibility for any damage in absence of floor

drainage.Humidity will naturally increase in the room where

the hot tub is located and the evaporated water condenses.

For this reason ensure that the area has proper ventilation.

We recommend installing a dehumidifier in the room.

2. OUTROOR AND PATIO INSTALLATION

A solid horizontal foundation is necessary for installation of

the hot tub. We advise using a reinforced concrete founda-

tion at least 10-15cm thick.

Ensure that your deck or foundation will support your hot tub.

You must know the maximal load capacity of the foundation.

Consult a qualified building contractor or structural engineer.

To find out the weight of your hot tub, its contents and

occupants please refer to the hot tub specification chart. This

weight must not exceed the structure’s rated capacity per

square meter, otherwise serious structural damages could

result. If you install the hot tub outdoors, we recommend a

reinforced horizontal concrete pad at least 10-15cm thick.

Install floor drains around your hot tub to lead water away

even in heavy rain.

When constructing the water drain it is advised to form a

10-15cm deep sloping ditch around the hot tub which directs

water to the drain. Water from the drain must be directed to

the canal or a drainage with enough capacity.

Warning: Do not expose the hot tub to direct sunlight (not

even empty) without proper coverage. The insulated hot tub

cover preserves the water temperature and provides protection

from sunlight and rain. When exposed to sunshine for a longer

period it may damage the surface of the hot tub and the hot tub

equipment.

Acrylic rapidly absorbs heat from sun rays, thus reaches a very

high surface temperature which may damage the hot tub.

In case of sealed design, if the hot tub was placed between

glass structures, prevent the sun rays from reaching the hot

tub directly through the glass as the temperature may get

too high.

3. IN-GROUND / SUNKEN HOT TUB

In case of sinking the hot tub into the ground you must

make sufficient space for walking around the hot tub. For

completion of maintenance works a minimum of 60cm wide

inspection pit must be built around the hot tub.

The inspection pit’s bottom must be under the bearing pont

of the hot tub so that water can flow into the pit in case of

water leakage. A floor drain or sump pump should be used at

the bottom of the pit to ensure continual water drainage.

In case of sinking the hot tub only the portion below the hot

tub’s acrylic edge can be sunk. The air of the inspection pit

steams up. To prevent unpleasant odors proper ventilation

must be provided (e.g. installing ventilators). The costs of

pulling the hot tub out of the ground are borne by the user.

If the aforementioned conditions are not present, setting up

the hot tub may fail.

First filling of the hot tub

Proper filling of the hot tub is an important task both tech-

nically and chemically. We advise installation and periodic

maintenance by the servicing professionals, which includes

inspection and refilling of hot tub water. Hot tubs do not con-

tain water softener and hard water damages the equipment.

Improper filling of the hot tub may bring air into the system,

which damages the heating wire and engines. Repairs after

such failures are not covered by warranty.

Filling process

Remove the hot tub cover. First remove the cover staves,

then remove the side covers by unscrewing the bottom

screws. During transportation the flare fittings of engines

may dislocate. Check these connections before installation. If

necessary, tighten the flare fittings.

In hot tubs equipped with air engine the flare fitting must be

connected before running the hot tub for the first time.

Before filling the hot tub check that the ratchets are not in

a closed state (lever is pulled out and fixed with the safety

lock).

Next fill the hot tub with water to the sign indicated on its

sidewall.

Filling must be done through the filter housing. Improper

filling can damage the engines and heating element.

Insert the filter or filter cartridges when proper water level

is reached. Be cautious, because when replacing the filter

cartridge air bubbles may remain in the cartridge. To avoid

this the filter cartridges must be tilted in the water to remove

air from them, and only then fitted to their place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bueno Spa Boston Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info