678367
44
Zoom out
Zoom in
Vorherige Seite
1/93
Nächste Seite
DiffServ Policy
Select the action for when the frames satisfy the condition.
Permit
Permits forwarding the frames and packets.
Deny
Discards the frames and packets.
Egress Queue
Changes the processing priority of the frames and packets.
Remark CoS
Rewrites CoS value of the frames and packets.
Remark DSCP
Rewrites DSCP value of the frames and packets.
Remark IP Precedence
Rewrites IP precedence value of the frames and packets.
Profile Action
Processes the frames and packets depending on the committed rate. If the rate
of the frames and packets is less than the committed rate, the switch will process
the frames and packets in accordance with the in-profile action. Otherwise, the
switch will process the frames and packets in accordance with the out-of-profile
action.
Committed Rate
Specify the rate to determine the process method.
Committed Burst
Specify the burst size that the switch processes in accordance with the in-
profile action when the rate of frames and packets exceeds the committed rate
instantaneously. When the burst size exceeds the committed burst, the switch
will process in accordance with the out-of-profile action.
In-Profile Action
Specify the action when the rate of frames and packets is less than the committed
rate.
Out-of-profile Action
Specify the action when the rate of frames and packets exceeds the committed
rate.
About Address and Mask
This product adopts “wildcard masks”.
To configure the source MAC address or destination MAC address, refer to the following example.
To specify the range of “00:11:22:ab:cd:00” to “00:11:22:ab:cd:ff
Enter “00:11:22:ab:cd:00” in the address field and also enter “00:00:00:00:00:ff in the mask field.
To specify only “00:11:22:ab:cd:ef
Enter “00:11:22:ab:cd:ef in the address field and also enter “00:00:00:00:00:00” in the mask field.
To configure the source IPv4 address or destination IPv4 address, refer to the following example.
To specify the range of “192.168.1.0” to “192.168.1.254”
Enter “192.168.1.0” in the address field and also enter “0.0.0.255” in the mask field.
To specify only “192.168.1.1”
Enter “192.168.1.1” in the address field and also enter “0.0.0.0” in the mask field.
43
Chapter 2 Settings
44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Buffalo BS-GS2016 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info