678326
218
Zoom out
Zoom in
Vorherige Seite
1/245
Nächste Seite
217
Chapter 8 Drive Replacement
Replacing SSDs on the TS5210DF Series When Data
Protection Mode Is Enabled
When data protection mode is enabled, a warning message to notify you that too many bad blocks have been
detected on the drive after logging in to Settings. In such a case, back up data on the drive and replace it. When a
drive with bad blocks is replaced in a RAID 0 or JBOD array, all data on the array will be lost. The procedure
may vary depending on what RAID mode you have configured. Do not perform the following procedure unless the
bad blocks warning message appears and data protection mode is enabled. If another drive error message such as
the E30 message appears, follow the replacement procedure described at the “Replacing Drives on Another Unit
Series Other Than the TS51210RH Series” section above.
Using RAID 1
When too many bad blocks occur on both drives in the RAID array, the TeraStation will be in data protection mode. If
both drives need replacement, replace them one by one.
1 From Settings, click Storage.
2 Click to the right of “Drives”.
3 Select a drive and click S.M.A.R.T. to check whether the current value of “Reallocated_Sector_Ct” is 99 or less.
4 Click Close.
5 Select a drive whose current value of “Reallocated_Sector_Ct is 99 or less and click Dismount Drive.
6 The “Confirm Operation” screen will open. Enter the confirmation number, then click OK.
7 When the dismount process is completed, the TeraStation will beep and the I12 and E30 messages appear.
Press the display button to stop the TeraStation beeping.
8 Open the front panel with the included key.
9 The dismounted drives status LED will be glowing red. Push its unlock button and swing the lock mechanism
out.
10 Pull out the drive cartridge and remove it from the TeraStation.
11 Insert the new drive into the empty slot. Slide the drive in with the locking mechanism open.
12 Swing the lock back down until it clicks into place.
13 Close the front cover.
14 When the replaced drive is recognized, the status LED will flash red and the I32 message will appear on the
LCD panel.
15 Press the function button on the front of the TeraStation. The TeraStation will beep and start rebuilding the
RAID array automatically. After a few minutes, the I18 message will be displayed until the array is rebuilt.
16 After the rebuilding process is completed, repeat the steps 5–14 for another drive with bad blocks.
218

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Buffalo TeraStation 5810 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Buffalo TeraStation 5810

Buffalo TeraStation 5810 Bedienungsanleitung - Deutsch - 259 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info