Bedienungsanleitung Buffalo TeraStation WS5400 (Seite 112 von 117) (Englisch)

678319

112

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

This recovery procedure erases your data. Backing up regularly is highly recommended to avoid losing your

important data.

Do not connect the SD card to another TeraStation or your computer. The recovery process that involves using this

SD card is intended for this product only.

Recovery is performed by deleting the area for drive 1, setting up a new 100 GB (Basic Disk/Simple) area, and

then copying the Windows Storage Server image to this area.

Note: If there are system areas (or mirrored locations) on hard drives other than drive 1, be sure to delete

the system areas (or disable the mirrored locations) before performing the recovery procedure. If recovery is

performed without deleting these areas, Windows Storage Server may not run after recovery is performed.

If Windows Storage Server fails to run, turn off the TeraStation and perform the recovery procedure again

while all hard drives except for drive 1 (disk 0) are disconnected. After recovery is complete, reconnect the

disconnected drives, which will appear in “Disk Management” as “Foreign”. In “Disk Management”, right-click

Foreign, select Import Foreign Disks, then right-click this area and click Reactivate Volume to rebuild the RAID

volume.

1 Turn off the TeraStation, following the procedure on the “Turning the TeraStation On and Off” section in

chapter 1.

2 Insert the SD card into the card reader (not included).

3 Connect the card reader to the TeraStation using a USB 3.0 or 2.0 port.

4 Set the boot mode switch to “USB”, then press the power button.

This executes the recovery process.

5 The TeraStation shuts down automatically when the recovery process is complete.

6 Remove the card reader, set the boot mode switch to “HDD”, and press the power button.

When the initial setup is complete, the TeraStation will reboot into Windows Storage Server.

After the recovery process is completed, the TeraStation is set to the state below when running under default

settings.

• Drive 1

100 MB (EFI System partition)

100 GB (Basic Disk/Simple)

The remaining space is an unallocated area.

• Drives 2–6

The data on the drives cannot be viewed. They appear as a “Foreign” in “Disk Management”.

Note: The data on the drives can be viewed by right-clicking the area displayed as “Foreign” in “Disk Management”

and then selecting Import Foreign Disks.

Notes

Using an Omron UPS

The TeraStation’s LCD panel will not display information correctly when an Omron UPS is first connected. This is be-

cause the LCD panel control and the Omron UPS both use COM port 2. To resolve, refer to the Omron’s user manual

and change its UPS communication port to a port other than COM 2, then restart the TeraStation.

111

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Buffalo TeraStation WS5400 Seite 112

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Buffalo TeraStation WS5400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info