Bedienungsanleitung Bugatti Vela evolution (Seite 12 von 16) (Englisch)

623954

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Advice and recommendations on use

Installation and starting up

5) Insert the lid (2) assembled with the filler cup (1) into the mouth of the assembled jar (3).

6) The blender has a safety lock that prevents the motor from being activated unless the blade unit (5) is

perfectly assembled with the jar (3) before it is i nserted into the motor base (6)

7) After making the above checks, and complying strictly with the safety instructions, connect to the mains

power supply.

Connecting to the power supply: electric current can kill. Comply strictly with the safety instructions.

The Vela blender must be connected via the power cable (7) to a socket the voltage of which complies

with the voltage indicated on the rating plate under the blender.

Before unplugging the blender, make sure that it has come to a complete standstill. Check that the

speed selector (12) is set at zero (0), wait for the current task to finish and then remove the plug from

the wall socket. Never remove the plug from the socket by pulling on the cable.

Make sure that socket that you are using is gounded ( )

Never use defective or damaged cables.

Never allow parts carrying live voltage to come into contact with water: you may cause a short circuit!!!

(adhere strictly to all points of the safety instructions specified above).

A. Using functions with 4 speeds

1) Adhere strictly to all safety, installation and instructions specified above.

2) Make sure that the speed selector (12) is at zero (0) and then insert the plug (7) into the socket. Make

sure that the your socket is adequately grounded ( )

3) Once the plug (7) has been plugged in the red light (11) comes on. This is an important signal that indicates

that the blender is connected to the power supply and is therefore carrying live current.

4) Insert the jar (3), which has been assembled according to instructions, into the motor base (6).

5) Remove the lid (2) and measuring filler cup (1) from the jar (3).

6) Place the food that you are going to blend in the jar (3) (without exceeding the maximum permitted level

of 1.5 litres – 50 onzs) and put the lid (2) complete with the measuring filler cup (1) back on the jar (3).

7) Cut the food into cubes measuring approximately 1.8 cm (3/4") by 2.5 cm (1 ") to obtain the ideal result

8) Hold the jar (3) handle firmly with one hand and turn the speed selector (12) to the desired speed (low=1,

medium=2, high=3, maximum=4). WARNING: always keep a hand on top of the lid whilst the motor is running.

9) To switch off, turn the speed selector (12) to the zero (0) position.

10) Before removing the jar, disconnect the plug (7) from the socket. WARNING: Do not pull on the cable

to unplug.

11) To remove the jar (3), take hold of the jar (3) by the handle and lift it up vertically to remove it from

the motor base (6). To pour the blended food, remove the lid (2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bugatti Vela evolution Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bugatti Vela evolution

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info