Bedienungsanleitung Bulls Ebikes - BOSCH Purion 2021 (Seite 69 von 196) (Englisch)

779909

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

MY21B01 - 32_1.0_17.08.2020 69

Operation

10 Measure the distance between the dust wiper

and the O-ring or cable tie.

This measurement is the negative deflection.

The recommended value is between 15%

(hard) and 20% (soft) of the total fork

deflection.

11 Increase or reduce the air pressure until you

have reached the desired negative deflection.

If the negative deflection is correct, turn the

blue valve cap in a clockwise direction.

6.5.7.2 Adjusting the rebound

The rebound defines the speed at which the fork

rebounds after being loaded. The rebound setting

depends on the air pressure setting. A higher

negative deflection requires a lower rebound

setting.

1Turn the FOX rebound adjuster in a clockwise

direction to the closed position until it stops.

Figure 73: FOX rebound adjuster (1) on the fork end

2Turn the FOX rebound adjuster slightly in an

anti-clockwise direction.

3Adjust the rebound in such a way that the fork

rebounds quickly, but without bottoming out

upward. Bottoming out refers to when the fork

rebounds too quickly and stops moving

abruptly once it has reached the full rebound

distance. You can hear and feel a slight impact

when this happens.

6.5.8 Setting the Suntour rear frame

damper

Only applies to pedelecs with this equipment

6.5.8.1 Adjusting the negative deflection

Negative deflection depends on the rider's weight

and sitting position. The recommended negative

deflection should be between 25% and 30% of the

total rear frame damper deflection, depending on

preferences and pedelec use.

When adjusting the negative deflection, ensure

that the compression adjuster is in an open

position, i.e. the lockout lever is in the OPEN

position.

1Remove the valve cap from the air valve.

2Attach a high-pressure damper pump.

3Adjust the rear frame damper air pressure to

the rider's weight.

4Detach high-pressure damper pump.

5Measure the distance between the air chamber

seal and the end of the rear frame damper.

This gap is the total rear frame damper

deflection.

6Put on your normal cycling clothing, including

luggage.

7Sit on the pedelec in your usual riding position

and support yourself against an object, such as

a wall or tree.

8Push the O-ring downwards against the air

chamber seal.

9Get off the pedelec without the suspension fork

deflecting.

Measure the distance between the air chamber

seal and the O-ring. This measurement is the

negative deflection. The recommended value

is between 25% (hard) and 30% (soft) of the

total rear frame damper deflection.

If you are unable to achieve the desired negative

deflection, internal settings may need to be

changed. Contact your specialist dealer.

Notice

If the air pressure in the rear frame damper is

exceeded or undershot, the damper can be

permanently damaged.

Do not exceed the maximum air pressure of

300 psi (20 bar).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bulls Ebikes - BOSCH Purion 2021 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bulls Ebikes - BOSCH Purion 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info