Bedienungsanleitung Burley Nomad 2007 (Seite 6 von 11) (Englisch)

632536

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

10 B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L

B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 11

Installing the Safety Flag

Nomad

™

: Join the two ﬂag pole sections together. Insert the ﬂag pole into the

ﬂag pocket on the inside of the left side panel. DO NOT USE YOUR TRAILER

WITHOUT THE SAFETY FLAG IN PLACE.

Hitching Your Burley to Your Bicycle

The Burley standard trailer hitch was designed to quickly and safely attach

to virtually all types of bicycles. It is attached to the left rear dropout (the

non-chain ring side) of your bicycle.

1. Remove the quick release lever assembly from your bike and set it aside.

2. Line up the hole on the ﬂat side of the hitch upper arm with the left

rear dropout hole.

3. Reassemble the quick release assembly through the hitch and dropout,

but don’t tighten it yet.

4. Slide the hitch receiver end of the tongue between the two hitch side

arms, and line up the holes. The hitch should clear any racks, bags, or

ﬁttings you have on your bicycle. If there is any interference, contact

your Authorized Burley Dealer.

5. Open the retaining pin and insert the pin through the holes.

6. Rotate the pin’s spring clip and close the pin.

7. Now tighten the quick release lever, with the lever pointing to the rear

of the bike. When properly adjusted, you will feel resistance halfway

through closing the lever (when the lever is pointing straight out away

from the bike).

8. Wrap the safety strap around the inside of the chain stay twice and then

over the hitch body. Fasten the hook to the D-ring on the underside of the

tongue end.

The quick release lever must be in the closed position. Do not operate

the trailer without the hitch safety strap properly installed. A dangling

safety strap can contact the spokes and damage the rear wheel or

cause an accident, resulting in serious injury. Inspect the hitch and

tongue frequently for damage or loose fasteners. Interfering parts or a

damaged hitch can cause an accident, resulting in serious injury.

WARNING

Loading Your Trailer

Maximum trailer load limit for both the Burley Nomad and the Burley

Flatbed is 100 lbs. When placing cargo into the Nomad trailer, keep the load

centered or forward of the axle. Pack the load as low as possible and make

sure items cannot shift around. When loading cargo on the Flatbed, always

ensure that the load is adequately fastened and centered on the trailer ﬂoor.

Cargo can be fastened by rope, cargo tie-down cords, netting, or within a

container that is securely fastened to the Flatbed trailer. Do not permit the

cargo to extend past the perimeter of the fabric ﬂoor on either side. Objects

loaded too close to the wheels when the trailer is stationary risk catching in

the spokes or interfering with the wheels when the trailer is in motion. The

area in front of the trailer frame must also remain clear to avoid interfering

with the bicycle’s rear wheel. Objects that extend beyond the rear can ob-

scure the reﬂectors, cause an unstable weight balance on the bicycle’s rear

heel, or contact the ground on uneven terrain. Do not overload the trailer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Burley Nomad 2007 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info