Bedienungsanleitung Bushnell Onix 400-2 (Seite 9 von 32) (Englisch)

481956

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1. You must charge the battery pack before using the ONIX400. Attach the battery pack (ﬁrst, verify

that the MicroSD card is installed in its slot), referring to the instructions and photos on pg. 5. Plug

the AC charger cord into the accessory port (pg. 6), then into an AC outlet (110-120 volt/60 cycle).

2. The initial charge may take up to 4 hours. A full charge is indicated when the status LED below the

orange Hot button changes from red to green. You may then disconnect the charger cord from the

outlet and accessory port. Store it safely for future use.

3. To ensure adequate satellite signal strength, make sure you are in a location with an unobstructed

view of the sky (GPS units typically do not work well indoors unless you are very near to a window)

4. Press and hold the power button for a few seconds until the display starts up.

5. Press the MENU button brieﬂy. You will see the Main Menu screen, with seven “pages” to choose

from. Use the 5-way switch to select (highlight) S AT, then press the “OK” (center) button.

6. You are now viewing the Satellite (SAT) page. You will begin to see multiple icons on the circular

“radar” screen, representing the closest satellites to you in the global GPS system. These icons will

turn green as the ONIX “locks on” to each satellite, and the satellite ID# will be shown. The bar graph

below the “radar” screen indicates the relative signal strength of each satellite. Once you have a lock

on at least 3 or 4 satellites, you are ready to navigate. Note that the satellite “lock” process will take

longer (up to 3 or 4 minutes), the ﬁrst time you use your GPS in a new geographical area, but will be

much faster on future usage in the same area

(see “Reset Data” in the SET Page>GPS options, if you

later relocate more than 300 miles away from your initial area)

. You can check reception with the SAT

page at any time, but will likely ﬁnd that you use it less than any other page-in fact, you may simply

go directly to the MAP (or any other) page the next time you use your ONIX.

7. You’re ready to go! Let’s take a look in more detail at the other pages, then see how easy it is

to enjoy the many features and capabilities of the ONIX400 for yourself to mark and name your

own waypoints (locations or objects you want to return to later), navigate towards a nearby point

of interest, layer a compass or weather radar over the map, and even listen to a ball game or your

favorite music while you walk!

GETTING STARTED

To use the XM Satellite Weather and/or Entertainment features of the ONIX400,

you will ﬁrst need to set up your subscription to these XM services and activate

XM reception for your unit. It’s fast and easy... just follow the directions on the “XM

Satellite Service Activation” page included in your ONIX information pack, or call

1-800-985-9200. In order to activate the XM Radio services, you will need your XM

Radio ID number. This ID# can be found on the product label inside the battery pack

compartment, or on the SET page in the “Unit Info” (Go to the SET page, press UP or

DOWN buttons to highlight “Unit Info”, then press the OK button to display all unit

info, including your XM ID number).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bushnell Onix 400-2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info