Bedienungsanleitung Byron SX-15 (Seite 2 von 2) (Englisch)

532522

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Door Bell Operation

Press the button on the push button unit once, the LED indicator will light up

during signal transmission for 1 second and the door chime unit will sound.

The sound will stop as soon as the melody ends. For repeat sound, press the

button again. Holding the button in will NOT repeat the sound.

Sound Adjustment

To slightly adjust the sound of the bell, loosen the screw

that holds the dome in place. Turn the dome and then

tighten the screw.

Important

1. Do not mount the Push Button unit onto any metal or

UPVC doorframe as this will reduce the operating

range.

2. Do not immerse either unit in water.

3. Do not expose either unit to high temperatures or

close to fireplace.

4. Do not use different type of batteries, or mix up old

and new batteries.

5. Do not leave exhausted batteries in either unit. If leaving the doorbell for a

long period of time, remove the batteries from all compartments to prevent

leakage.

6. The chime unit is designed for internal use only.

7. Please dispose of old, defective batteries in an environmentally friendly

manner in accordance with the relevant legislation.

8. The unit should not be exposed to or placed near sources of water or direct

heat.

9. Replace batteries only with the same or equivalent type recommended by the

manufacturer.

10. Do not place near a P.I.R. which may interfere with your chime.

3. Select any combination ensuring it is set to the same code on both push

button and door chime units. E.g. If the 1 & 2 dipswitches are down in

your push button, then the 1 & 2 dipswitches must be down in your

chime unit.

4. Test to ensure correct operation before final installation.

Trouble Shooting & User Hints

Problem

Chime does not

sound but LED

lights on Push

Button

Possible Causes

1. Units is out of range (max.

range 100m)

2. Push button and chime not

on same channel

Suggested Remedy

Operate the Chime unit within the

operation range (100m)

Re-set the channel (see Channel

Set Up)

Chime does not

sound plus no

lights on Push

Button LED

1. Flat push button battery

2. Wrong polarity of battery in

push button

3. Remove the protective Strip.

Change the battery

Re-insert battery as internal

marking in right polarity

Chime sounds

without push

button being

pressed

A similar wirfree door chime

product is operating nearby

on the same transmitter

frequency

Change transmission channel

(see Channel Set Up)

NOTE: There are no serviceable parts in the unit, do not attempt to repair it.

Specification

A. Push Button unit

Power

Consumption

: 2 x 3volt Lithium batteries (CR2032 - included, replace with

Byron model SX-100)

: 3.0mA - ON

0.003mA - OFF

B. Door Chime unit

Power

Consumption

Operating Temperature

Operating Distance

Selectable Channel

: 2 x 1.5volt batteries (“D”, R20 or UM1 - not included)

Alternatively powered by A/C-D/C 9volt 300mA

adaptor (Byron model SX-36 - not included)

: 100mA - ON

0.3mA - Stand-by

: -10°C to +40°C

: 100 metres (320 feet approx.) in open field

: Total sixteen (16) possible channels

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Byron SX-15 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info