Bedienungsanleitung Byron SX-209 (Seite 2 von 2) (Englisch)

532517

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

1. Do not mount either unit close to fireplace or expose to high temperatures.

2. Do not expose the Door Chime unit to direct sunlight or moisture.

3. Make sure that no naked flame sources, such as lighted candles, are placed on the unit.

4. The unit should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,

shall be placed on the unit.

5. CAUTION: Replace only with the same or equivalent type of battery that is recommended by the manufacturer.

6. CAUTION: Danger of explosion if battery is incorrectly installed or replaced.

7. CAUTION: This product is not suitable for people who suffer from epilepsy due to flashing light.

Model No. SX-209

Important

R&TTE

approved

Press the button on the Push Button unit once, it sends a wireless

signal to the Door Chime and will activate one of the following

functions:

a) Sound and Light: The Door chime will sound as well as the

Super Bright Light flashing to

maximize attention.

b) Light Only: The Super bright Light on the Door Chime

unit will flash.

c) Sound Only: Door Chime unit will sound.

The function selector is located at the back of the unit, press the

buttons to select the function to operate the chime unit

accordingly. For repeat sound, press the button again. Holding the

button in will NOT repeat the sound.

Door Chime Operation

It is located at the side of the item, slide the switch to adjust the light function as follows:

a) Sound Only

b) Strobe Light Only

c) Sound + Strobe Light

It is located at the back of item, press the button to adjust the sound volume goes up and down. There is a total

of 8 different sound volume levels set, 1=mute and 8 =max level, the door chime will start operating at sound

level 6 initially.

Volume

Control

The unit comes from the factory on a pre-set radio frequency digital

code. However, should your door chime activate intermittently for no

reason at all, it is possible that a similar unit is operating nearby on the

same frequency digital code. The encoded frequency of the Push Button

(transmitter) can be changed to avoid this problem. The Door Chime

unit is equipped with an advanced self-learning operation code ability

therefore no setting is needed.

Digital Code Set Up

1. Remove the back of the case from the Bell Push unit.

2. There are 4-position dipswitch marked 1,2,3 & 4. Use an screwdriver

to alter the dipswitch levers to the “On/Off” position, which can be

altered to achieve a total of sixteen (16) possible digital codes.

3. Select any combination on the Push Button. Press the Push Button,

the Door Chime unit will sound to indicate that new operation code

is registerd and memorized, and it will only work with it.

4. To re-set the operation code, simply remove the batteries from the Door Chime unit and rest for 30 seconds,

it will erase the memory. Re-insert the batteries into the Door Chime unit, it will give 2-beeps to indicate that

it is ready for new code registration. Press the Push Button to confirm the new code is working.

5. Test to ensure correct operation before final installation.

Push Button

Eg.

A. Push Button unit

Power

Consumption

: 1 x 3 volt Lithium battery (CR2032 - included)

: 7.0mA - ON

0.003mA - OFF

B. Door Chime unit

Power

Consumption

Operating Temperature

Operating Distance

Selectable Tone

Selectable Digital Code

: 2 x 1.5 volt alkaline batteries (“C”, UM2 & R14 - included)

: Sound Only-200mA, Strobe Light Only-200mA, Sound+Light-350mA / 0.3mA-Stand By

: -10∞C to +40∞C

: 100 metres (320 feet approx.) in open field

: Total eight (8) tones available

: Total sixteen (16) possible digital codes

Problem

Chime does not

sound but LED lights

on Push Button

Chime does not

sound plus no lights

on Push Button LED

Chime sounds

without Push Button

being pressed

Possible Causes

1. Units is out of range (max. range 100M)

2. Push Button and Chime units are not on

same digital code

1. Flat Push Button battery

2. Wrong polarity of battery in Push Button

A similar Wire Free Door Chime product is

operating nearby on the same frequency

digital code

Suggested Remedy

1. Operate the Chime unit within the

operation range (100M)

2. Re-set the digital code

(see Digital Code Set Up)

1. Change the battery

2. Re-insert battery as internal marking

in right polarity

Change the digital code

(see Digital Code Set Up)

Important: There are no serviceable parts in the unit, do not attempt to repair it.

Trouble Shooting & User Hints

Specification

Type R2 Device - device where the sound output is created by the initial operation of the control and where the

period of sound output continues for designed duration irrespective of condition of the control.

• Sound

• Strobe Light

• Sound +

Strobe Light

Light Option Control Button

Sound Volume Control Button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Byron SX-209 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info