SX Range Bell Push SX-35
SX Range Bell Push SX-35
Byron No.SX35 Size: A4 Date: 11 Oct 2007
3. Feed the wire via the hole on the back of the Push Button and connect the wire to the terminal
positions A & B as marked.
4. Snap the back cover of Push Button back on, then it is ready to use.
Important: Do not connect the Wireless Push Button unit with any Lighted Bell Push.
Important
1. Do not mount either unit close to fireplace or expose to high temperatures.
2. Do not expose the Door Chime unit to direct sunlight or moisture
3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally
friendly manner in accordance with the relevant legislation.
4. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.
5. The unit should not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, should be placed on the unit.
6. CAUTION: Replace only with the same or equivalent type of battery that is recommended by the
manufacturer.
7. CAUTION: Make sure batteries are installed correctly as per the internal marking.
8. CAUTION: Danger of explosion if battery is incorrectly installed or replaced.
9. IMPORTANT: There are no serviceable parts in the units, do not attempt to repair it.
User Hints
If the door chime unit does not sound, please check the following:
a) Flat batteries in either Push Button or Door Chime units - change the batteries.
b) Wrong battery polarity in either Push Button or Door Chime units - re-insert the batteries.
c) Push Button or Door Chime units are not on the same operation codes - re-set the code (see
digital code set up).
d) Units are out of range - Operate the Chime unit within the operation range.
Specification
Operating Temperature: -10C – +40C
Selectable Tone: Total Eight (8) melodies available
Selectable Digital Code: Total two hundred fifty six (256) possible digital codes
“Type R2 Device - device where the sound output is created by the initial operation of the
control and where the period of sound output continues for the designed duration
irrespective of condition of the control.”
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
CH Byron Electrical Ltd
Byron House
34 Sherwood Rd, Astonfield
Bromsgrove, B60 3DR
UK
Tel: 0845 2301231
e: support@chbyron.com
w: www.chbyron.com
A B CA B C
Push Button
• Open up the push button by pushing in the tab at the
bottom of the push with a small flat screwdriver.
• Remove the isolation strip from the battery
compartment then it is ready to use.
• When replacing the battery, ensure the battery
polarity matches the internal markings (“+” facing
upwards), then press the battery down so that it is
sitting firmly in its compartment.
CR2032 3V
Lithium
Battery
Remove
Isolation
Strip
1 2
Melody Selection
Press the melody selector once to select a melody as
your Byron SX Range door chime sound.
3
Digital Code Set Up
• Press the Push Button once, a new operation code is
generated randomly and sent to the Door Chime unit.
• The Door Chime will sound to indicate that a new
operation code is registered and memorised.
4
Push Button Installation
• Using the holes on the back of push button as a
template, mark the fixing position for the unit.
• Drill holes and fit wall plugs and secure the push
button unit to the wall with screws.
• Do not mount it on any metal surface or UPVC door
frame.
A B CA B C
A B CA B C
Melody Selector
5
Wiring Installation
The Push Button can be used as converter to change your existing Wired Bell Push to wire free.
1. Connect your Wired Bell Push cable to the built-in terminal positions A & C of Wireless Bell Push.
2. Your Wired Bell Push with Wireless Push Button is ready to use.
In case a Transformer (A/C 8V) is used to power the Wired Bell Push and Wired Door Chime.
1. Remove the back of case by pushing in the tab on the bottom with a small, flat screwdriver.
2. Disconnect the wire that connected with Wired Door Chime.
3.
Feed the wire via the hole on the back of the Push Button and connect the wire to the terminal positions A & B as marked.
4. Snap the back cover of Push Button back on, then it is ready to use.
Important: Do not connect the Wireless Push Button unit with any Lighted Bell Push.
1.
WIRED
CHIME
(Transformer
operation)
3.
WIRED
CHIME
(Transformer
operation)
2.
A B CA B C
A B CA B C
Important: This Bell Push is designed to work with Byron SX Range Door Chime only
Push Button unit
Power: 1 x 3volt Lithium battery (CR2032 - included)
Melody Selection
Press the melody selector once to select a melody as your Byron SX Range door chime
sound.
Digital Code Set Up - When work with Byron SX Range Door Chime
The Door Chime kit is equipped with an advanced random and self-learning operation
coding ability therefore no setting is needed. Read the following instructions before use.
1. First time operation:
After battery installation on the Push Button and Door Chime units, press the Push Button once
and it will generate a new operation code randomly and send a wireless signal to the Door Chime
unit. The door chime will sound to indicate that a new operation code is registered and
memorised.
2. Interference from a similar unit operating nearby:
a) Simply remove the batteries from the Push Button and Door Chime units and rest for 10
seconds, this will erase the memory.
b) Insert the batteries into the Push Button and Door Chime units, the door chime unit will give
2-beeps to indicate that it is ready for the new code registration. Press the Push Button once,
it will generate a new operation code randomly and send a wireless signal to the Door Chime
and it will sound to indicate that a new operation code is registered and memorised.
3. Front and back door Bell Push operation:
a) Remove the batteries from the Push Buttons (Front & Back Door) and Door Chime units and
rest for 10 seconds, this will erase the memory.
b) Insert the batteries into the Push Buttons and Door Chime units, the door chime unit will give
2-beeps to indicate that it is ready for the new code registration.
c) Press the front door Push Button once, it will generate a new operation code randomly and
send a wireless signal to the door chime unit and it will sound to indicate that a new operation
code is registered and memorised.
d) After, (within 2 minutes) press the back door Push Button once, it will generate a new
operation code randomly and send a wireless signal to the door chime unit and it will sound to
indicate that a new operation code is registered and memorised. The door chime unit has the
ability to memorise both operation codes.
e) Test to ensure correct operation before final installation.
Wiring Installation
The Push Button can be used as converter to change your existing Wired Bell Push to wire free.
1. Connect your Wired Bell Push cable to the built-in terminal positions A & C of Wireless Bell Push.
2. Your Wired Bell Push with Wireless Push Button is ready to use.
In case a Transformer (A/C 8V) is used to power the Wired Bell Push and Wired Door Chime.
1. Remove the back of case by pushing in the tab on the bottom with a small, flat screwdriver.
2. Disconnect the wire that connected with Wired Door Chime.
