Bedienungsanleitung Cadac 5650 - Grillo Chef 2 (Seite 3 von 8) (Englisch)

684173

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

2. Safety information

Hose

• The hose must be checked for wear or damage before every use and before connecting to the

gas container.

• Do not use the appliance if it has a damaged or worn hose. Replace the hose.

• Do not use an appliance that is leaking, damaged or which does not operate properly.

• The minimum hose length is 600mm and it is recommended that the maximum hose length

should not exceed 1.5m.

Gas Container

• This appliance must only be used with an approved hose and regulator. (A 2.8kPa hose and

regulator supplied only in South Africa)

• Ensure that the gas container is  tted or changed in a well-ventilated location, preferably

outdoors, away from any sources of ignition such as naked  ames, pilots, electric  res and

away from other people.

• Keep gas containers away from heat and  ame. Do not place on a stove or any other hot

surface.

• Re llable cylinders are to be used only in the upright position so as to ensure proper fuel

withdrawal. Failure to adhere to this may cause liquid discharge from the gas container

resulting in a dangerous operating condition.

• Do not try to remove the cylinder whilst the unit is in operation.

• The gas cylinder must be disconnected from the appliance after use or when in storage.

• Not for use with a remote gas supply.

Assembly and use

• Use only on a  rm level surface.

• Do not move the appliance during use.

• Ensure the appliance is used away from  ammable materials. Minimum safe distances are:

Above the appliance 1.2m. At the rear and sides 600mm.

• WARNING: Accessible parts may be very hot, the use of protective gloves is recommended. Keep

young children away.

• Use outdoors only!

Light back

• In the event of light back (where the  ame burns back and ignites inside the burner or venturi

housing), immediately turn off the gas supply by  rstly closing the control valve on the gas

cylinder and then the appliance valve. After the  ame is extinguished, remove the regulator

and check the condition of the seal; replace the seal if in doubt. Re-light the appliance.

• Should the  ame persistently light back, return the product to your authorized CADAC repair

agent.

Leaks

• If there is a leak on your appliance (smell of gas), turn off the cylinder valve and take it outside

immediately into a well-ventilated  ame-free location where the leak may be detected and

stopped. If you wish to check for leaks on your appliance, do it outside. Do not try to detect

leaks using a  ame; use soapy water.

• The correct way is to smear the joints with soapy water. If a bubble or bubbles form then there

is a gas leak. Immediately turn off the gas supply  rstly by closing the control valve on the gas

container and then the appliance valve. Check that all the connections are properly  tted. Re-

check with soapy water.

• If a gas leak persists, return the product to your CADAC dealer for inspection/repair.

3. Lighting the appliance

Precautions to observe before lighting.

• After prolonged storage, inspect the Air Holes in the Valve Cover for insects, which may affect

gas  ow. Inspect the inlet of the Venturi for insects. After checking, re t all components into

the prescribed position.

• Use this appliance only on a  rm level surface.

Using the control knob

The control knob is  tted with two positive stop positions, one at low, and one at Ignite / High.

This limits the adjustment of the  ame to between these two points.

Lighting up using the Piezo Igniter

• To light up the appliance using the piezo igniter, push in and turn the control knob in an anti-clockwise direction until you hear a click.

If the gas does not ignite on the  rst spark, push in, and turn the control knob fully clockwise. Try again, by pushing in and turning the

control knob anti-clockwise until you hear a click. If the gas has not ignited in the  rst two to three seconds you should close the control

valve by pushing in the control knob, and turning it fully clockwise. Wait approximately thirty seconds to let any accumulated gas within

the burner pan assembly escape. Repeat the above process if necessary until the  ame ignites. The  ame should normally light up within

the  rst one or two seconds.

Lighting up using a BBQ lighter

• When starting cold, the appliance may be lit from the top prior to  tting the desired cooking surface onto the fat pan. When lighting up

a hot appliance however, it is recommended that this be done by sticking barbecue lighter through one of the Vent Holes underneath the

Burner, until it is in line with the burner(DO NOT place the BBQ lighter through the large hole directly underneath the burner). Ignite the

BBQ lighter. Whilst the BBQ lighter is lit, push in and turn the control knob anti-clockwise to light the burner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac 5650 - Grillo Chef 2 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 5650 - Grillo Chef 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info