Bedienungsanleitung Cadac 6530L1 - Camp Chef LP (Seite 3 von 7) (Englisch)

684181

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

• If there is a leak on your appliance (smell of gas), close the cylinder valve immediately and take it into a  ame free location where the leak

may be detected and stopped. If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a  ame; use

soapy water.

• The correct way is to smear the joints e.g. where the stem  ts into the cylinder, with

soapy water.

• If bubbles form, then there is a gas leak. Immediately turn off the gas supply by

closing the control valve on the gas container and then the appliance valve. Check

that all the connections are properly  tted. Re-check with soapy water.

• If a gas leak persists, return the product to your CADAC dealer for inspection / repair.

• Use Outdoors Only.

Fig. 3

Fig. 5

Fig. 1

Fig. 2

Seal

Cylinder Valve

Fit hose

clamp

here

RegulatorHose

3. Assembly Instructions

• WARNING: The legs are spring loaded. Opening and closing of the legs must

be done in a controlled manner to avoid personal injury or damage to your

Camp Chef.

• To open the legs, turn the unit upside-down and hold the legs down while lifting

each leg individually. You will hear a “click“ if the leg(s) has located correctly.

• To fold the legs back, securely hold the leg and push the Leg Release Clip down.

Then push the legs in-ward to its closed position (Fig 6). This needs to be done

sequentially to optimise space. First the Right front leg (1), Then the

Left front leg (2), and lastly the rear Leg (3) (Fig 4b).

• Before connecting the gas supply,  rstly check that the appliance valve is in the off

position by turning the control knob fully clockwise (See Fig. 2).

• I 3B/P (30), I 3+ (28-30/37) and I 3B/P (37) Appliance categories: Fit the Valve

Tailpiece onto the Valve (Fig.5) by screwing it on in an anti-clockwise direction.

Push an 8mm inside diameter Hose onto the Valve Tailpiece until it is properly

seated. On the other end attach a suitable 30mbar low-pressure (I 3B/P (30) and

I 3+ (28-30/37) Butane con gurations) or 37mBar low-pressure regulator (I 3+

(28-30/37) Propane con guration), again making sure that the hose is well seated.

The hose used must comply with BS 3212 / SABS 1156-2 or equivalent.

• I 3B/P (50) Appliance category: Screw a Hose with the correct threaded  ttings on

each end, onto the left hand ¼“BSP thread of the Valve. Attach a suitable 50mbar

low-pressure regulator on the other end of the hose. The hose used must comply

with DIN 4815 part 2 or equivalent.

• Note: The hose and regulator are not supplied with the appliance. For details,

contact your local stockist.

• The hose length should be no less than 800 mm and shall not exceed 1.5 m.

Check the expiry date on the hose and replace when necessary or when national

conditions require it. Do not twist or pinch

hose.

• Your appliance is now ready for use.

OFF

Fig. 4a

Fig. 4b

Fig. 4a

Fig. 4b Fig. 4c

28-30 & 37mbar

ONLY

503-0573 LEV12 (6530L0, 6530L1) Camp Chef LP - User Manual - (EU + SA).indd 2 15/08/2017 13:09:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac 6530L1 - Camp Chef LP Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 6530L1 - Camp Chef LP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info