Bedienungsanleitung Cadac 8400 - LEISURE CHEF (Seite 4 von 11) (Englisch)

684185

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

4. Using the Appliance cont.....

? The BBQ Lid may be used with the Skottel BBQ, BBQ and Non-Stick Reversible

Grill options. When used with either the BBQ or Non-Stick Reversible Grill option, the BBQ Lid

locates on the outer lip of the Fat Pan. This gives a more direct type of heating for faster

cooking. When used with the BBQ for roasting, pour a cup of water in the Fat Pan to provide a

cleaner cooking environment.

Do not use the BBQ Lid on any of the above configurations with the appliance running at the full

(high) or intermediate (medium) rates.Use the BBQ lid configurations only at the reduced rate

(low) setting, this should produce more than enough heat for cooking under normal

circumstances. As this appliance has a high heat output, using more heat while cooking with the

BBQ Lid may cause damage to certain components. Refer to your enclosed Recipe Book for

mouth-watering recipe ideas to “Take Your Tastebuds On An Adventure”.

The BBQ Lid conveniently hooks onto the fat pan and is supported by means of two rubber

coated plastic brackets on the back legs. This is particulary usefull when you don’t want to use

the lid. It can also act as a windshield.

After prolonged storage, inspect the Air Holes in the Valve Cover for insects such as spiders,

which could affect gas flow. Also unclip the Valve Cover and inspect the inlet of the Venturi for

insects. After checking, refit all components into the prescribed position.

Use this appliance only on a firm level surface.

To light up the appliance using the piezo igniter, push and turn the control knob in an anti-

clockwise direction until you hear a click. If the gas does not ignite on the first spark, turn the

control knob fully clockwise and try again by pushing and turning the control knob anti-clockwise

until you hear a click. If the gas has not ignited in the first two or three seconds you should close

the control valve and wait approximately thirty seconds to let any accumulated gas within the

burner pan assembly escape. Repeat the above procedure if necessary until the flame ignites.

The flame should normally light up within the first one or two seconds.

To light the appliance, light a match or barbecue lighter. Open up the Control valve as described

under 'General” and light the appliance Burner. When starting cold, the appliance may be lit from

the top prior to fitting the desired cooking surface onto the Fat Pan. When lighting up a hot

appliance however, it is recommended that this be done by sticking the match or barbecue

lighter through one of the larger Vent Holes directly underneath the Burner.

Once the appliance is lit, the flame intensity may be adjusted by turning the valve knob anti-

clockwise to reduce the flame, or clockwise to increase the flame.

The fully closed position is at the furthest clockwise position. To rotate the valve from the fully

closed position it is necessary to first depress the knob just enough to move out of the lock

mechanism. While holding the knob in, turn it in an anti-clockwise direction. Once the spindle

has moved out of the lock position it is no longer necessary to keep the control knob depressed

and it can be rotated freely to the desired flame setting. (see fig. 5)

The control knob has a lock position at maximum flame setting. To rotate the valve to a fully

closed position it is necessary to depress the valve control knob just enough to allow the spindle

to move out of the lock mechanism at maximum setting.

The flame may be observed through the Inspection Hole provided for this purpose in the side of

the Fat Pan. (see fig. 6)

When cooking food with a high fat content, flaring may occur if the selected heat setting is too

high. Should this happen, turn the heat down until the flaring ceases.

Do not move the appliance when in use as, apart from being an unsafe practice, to move the

appliance whilst lit, may cause flaring.

After use, first close the valve on the gas container (where applicable). When the flame has

extinguished, close the valve on the appliance by turning the Control Knob fully clockwise.

BBQ Lid.

Precautions to observe before lighting.



Lighting up using the Piezo Igniter (see fig. 3)

Lighting up using a match or BBQ lighter

General

(see fig. 4)



Before fitting the regulator to a gas container, ensure that the seal on the regulator is in position

and in good condition. This should be done with every connection.

Ensure that the gas container is fitted or changed in a well-ventilated location, preferably

outdoors, away from any source of ignition such as naked flames or electric fires and away from

other people.

Making sure that the gas container is kept upright, screw the regulator onto the container until it

is fully engaged. Hand-tighten only.

If there is a leak on your appliance (smell of gas), take it outside immediately into a well-

ventilated flame-free location where the leak may be detected and stopped. If you wish to check

for leaks on your appliance, do it outside using soapy water only, which is applied to the joints. A

formation of bubbles will indicate the gas leak.

Check that all the connections are securely fitted and re-check with soapy water. If you cannot

rectify the gas leak, Contact your local CADAC stockist for

assistance.

When changing a gas container, firstly close the container valve (if fitted) and then turn the

Control Knob clockwise to its stop position. Ensuring that the flame is extinguished, unscrew the

regulator. Refit a full container following the same precautions as described above.

do not use the appliance.

5. Fitting and changing the gas container

Fig. 6

Fig. 3

Push and turn

‘click’‘click’

Fig. 4

Fig. 5

Cadac 8400 - LEISURE CHEF Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 8400 - LEISURE CHEF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info