Bedienungsanleitung Cadac Carri Chef 40 - 8905 (Seite 5 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

819978

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

2. Fitting and Changing the Gas Supply

Connecting the gas supply

• Before connecting the appliance to a gas supply, ensure that the rubber seal on the regulator is in position

and in good condition.

• Before connecting the hose and regulator to the appliance, check that the appliance control knob is in the

“OFF” position.

• Carry out this check each time you ﬁt the appliance to a gas cylinder.

• Blow out any dust from the gas supply opening to prevent possible blockage of the jet.

• Fit an approved hose and regulator to the appliance.

• Ensure that the gas supply (gas cylinder/gas cartridge) is ﬁtted in a well-ventilated location away from any

source of ignition, such as naked ﬂames and away from other people.

• Do not twist or pinch the hose. Ensure that it is routed away from the stove body so as to prevent

deterioration / damage to the hose caused by heat.

• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by screwing on hand

tight until fully engaged.

• Ensure that a complete gas seal has been made (check for the smell of gas around the connection

joint). Do not check for leaks with a naked ﬂame. Use warm soapy water only, applied to the joints

and connections of the appliance. Any leakage will show up as bubbles around the leakage area.

• If you cannot rectify the gas leak do not use the appliance. If you are in doubt, contact your

nearest stockist.

Disconnecting and changing the gas supply

• Aer use, turn the appliance control knob to the “OFF” position and close the gas supply.

• When you need to replace your empty cylinder, make sure that the gas is closed at the cylinder

valve.

• Do not smoke while changing the cylinder.

• Remove the regulator from the empty cylinder.

• Attach the regulator to the full cylinder, refer to the instructions above on how to connect the gas

supply.

• Apply the same care and checking procedures as if ﬁtting a new gas cylinder.

How to check if your gas cylinder is empty

• The easiest way to check if you are low on gas is by picking up your gas cylinder.

• If you think your gas cylinder is feeling a little lighter than you’d like, weighing the bottle is a great way to see how much gas is le. Most

cylinders will have the empty weight stamped on either the neck or foot ring, and if the weight indicated on the stamp and the weight of your

cylinder are the same, you’re out of gas. You can then approximate the amount of gas you have le by the diﬀerence in weight.

3. Operating the Appliance

Assembly and use

• The appliance is designed to be portable, therefore the legs and the utility tray are easily removable and dis-assemble for the ease of transport

and use.

• User assembly / dis-assembly is limited to the ﬁtment of the legs, utility tray and the installation / removal of cooking surfaces.

• When assembling the legs, always make sure that the legs are properly secured and that the assembled product is stable and does not rock.

Do not use the appliance without ﬁtting the utility tray as it also plays an important role in ensuring the overall sturdiness of the appliance.

• Should the heat shield, fat pan or burner pan become damaged in such a way that permanent contact between the heat shield and the fat pan

occurs during use, do not use the appliance. Return it to your stockist for repair.

• When operating this appliance, please take care to ensure that all parts are in good working order and that you have checked for any gas

leaks before lighting the appliance with every use.

• Cooking surfaces can simply be placed and are ready to use. No assembly required.

• PLEASE NOTE: Please ensure all protective packaging and plastic are removed from the appliance before use.

• The appliance is designed for use with cooking vessels of not less than 150mm diameter and not greater than 300 in diameter.

Precautions to observe before lighting.

• Use this appliance only on a ﬁrm level surface.

• Aer prolonged storage, inspect the appliance for any insects and webs, which may aﬀect gas ﬂow.

Lighting the appliance using the piezo

• To light up the appliance using the piezo igniter, push and turn the control knob (ﬁg.2) in an anticlockwise direction until you hear a click.

If the gas does not ignite on the ﬁrst spark, turn the control knob back to its “OFF” position. Try again, by pushing and turning the control

knob anti-clockwise until you hear a click. If the gas has not ignited in the ﬁrst two to three seconds you should close the control valve by

turing the control knob back to its “OFF” position.

• Wait approximately thirty seconds to let any accumulated gas within the burner escape. Repeat the above process if necessary until the

ﬂame ignites. The ﬂame should normally light up within the ﬁrst one to two seconds.

Lighting up using a BBQ lighter

• When starting cold, the appliance may be lit from the top prior to ﬁtting the desired cooking surface onto the fat pan. When lighting up a

hot appliance, it is recommended that this be done by sticking a barbecue lighter through one of the vent holes underneath the burner,

until it is in line with the burner (DO NOT place the BBQ lighter through the large hole directly underneath the burner). Ignite the BBQ

lighter. Whilst the BBQ lighter is lit, push and turn the control knob anti-clockwise to light the burner.

Gas inlet

Control knob

Fig. 2

Fit hose

clamp

here

Seal

Cylinder

Valve

Regulator

Hose

Fig. 3

Cadac Carri Chef 40 - 8905 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info