Bedienungsanleitung Cadac CARRI CHEF 8100 (Seite 11 von 13) (Englisch)

541597

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

10.General Maintenance

11.Cleaning



This appliance does not require scheduled maintenance.

Your Carri Chef is fitted with a specific size jet regulate the correct amount of gas.

Should the hole in the Jet become blocked, this may result in a small flame or no flame at all. Do not attempt to clean the Jet with a pin or

other such device as this may damage the orifice, which could make the appliance unsafe.

To replace the Jet :Unscrew the fitting connected to the inlet of the valve (O) before unclipping the valve cover (P1).

After cooking, leave the burner on low with soapy water in the cooking dish to soften cooking residue. When satisfied that

excess fat has been removed, wash the Skottel BBQ (I1) in warm water using a suitable non-abrasive detergent. Do not use sharp metal

objects or abrasive detergents on the vitreous enamel coated surface.

Remove the fat from the moat at the bottom of the Fat Pan (B) and clean as described for the Skottel BBQ. Wash the Grid

(H1) and Deflector Plate (H2) in warm water with non-abrasive detergent after wiping off any excess fat left after cooking.

: Wash the BBQ Lid (A) in warm water using a suitable non-abrasive detergent. Do not use sharp metal objects or abrasive

detergents, as this will damage the surface coating.

For stubborn stains, oven cleaner may be used.

The Non-stick reversible grill plate is coated with a tough durable non-stick coating that has been used with great success on some of the

best cookware in the world. Nevertheless, taking care of it can help you to enjoy extra years of healthy, easy, non-stick cooking.

Use only low or medium heat settings to help retain the valuable nutrients in the food and maintain the non-stick surface.

Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore recommended

that only plastic or wooden utensils be used when cooking.

Do not overheat the Non-stick reversible grill plate and always add a little cooking oil to the surface before use.

The non-stick coating is perfectly safe in the dishwasher, but the non-stick surface is so easy to clean that a quick hand-wash does the

trick. The use of abrasive detergents is not recommended, as this will permanently damage the non-stick surface.

After cleaning recondition the surface with a light wipe of oil.

Remove the fat from the moat of the Fat Pan (B) and clean as described for the BBQ above.

Replacing a Blocked Jet:

Note: For Parts Reference

Skottel BBQ:

BBQ:

BBQ Lid

Note:

Always allow the Non-stick reversible grill plate to cool before immersing it in water.

Use only low or medium heat settings to help retain the valuable nutrients in the food and maintain the non-stick surface.

Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore recommended

that only plastic or wooden utensils be used when cooking.

Do not overheat the Paella Pan and always add a little cooking oil to the surface before use.

Paella Pan:

Always allow the Paella Pan to cool before immersing it in water.



Care of the Non-Stick Reversible Grill Plate:

(Fig, 4) to

(See Fig. 9a-c)

that because the valve inlet has a left-hand thread, unscrewing any fitting requires clockwise rotation when viewed from the

fitting end of the valve. Remove the Control Knob by first removing the indicator cover and then loosening the screw holding the knob in

place, firmly pull the knob off of the valve spindle. Remove screw holding Valve Cover (P1) and remove cover by pulling it forward, past

the spindle. Undo the two screws located inside the Burner Pan that are holding the Valve Clip Cover (P2) and remove cover. the

Valve is now exposed. remove the 2 screws holding the valve in position and remove the valve by lifting it out of the valve box. Be very

careful not to pull piezo wire too much. Holding the valve, use a suitable spanner to loosen and remove the jet. Do not use pliers on the

jet as this may damage the jet, making it unusable or impossible to remove. Screw the new jet into the valve. Do not over-tighten as this

may damage the jet.

Reverse the above procedure to re-assemble the unit

Reconnect the gas supply as described in the Assembly Instructions.

The fitting of a hose is described in Section 6 - Assembly of the Appliance.

Remember

(See Fig.2)



Replacing the Hose:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac CARRI CHEF 8100 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac CARRI CHEF 8100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info