Bedienungsanleitung Cadac Safari Chef 30 - 6540H1 (Seite 9 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

819980

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

8. Maintenance & troubleshooting

Maintenance

• If you clean and maintain your appliance on a regular basis, the life of your appliance will extend and the possibility of problems will

decrease.

• We recommend the service of your appliance to be every twelve (12) months by a service agent to ensure continued eﬃcient operation.

• This appliance must only be serviced by an authorized person.

• Check your connections regularly for any signs of leaks and every time the gas cylinder is re-ﬁlled or ﬁtted to the appliance with every use.

Troubleshooting

In the case of a spattering ﬂame or jet blockage:

• Clean your burner ports in case of an over spill.

• We recommend to clean or replace the jets every six (6) months to ensure continued eﬃcient operation of your appliance.

• Should the appliance operate abnormally aer storage and all checks have not isolated the problem, the jet may be blocked. A blocked

jet would be indicated by a weaker yellowish ﬂame or no ﬂame at all in extreme cases. Under these circumstances it will be necessary to

remove and check and thoroughly clean out any foreign matter which may have gathered in the appliance.

• This may be done by removing the jet using standard tools and blow any dirt from the jet, alternatively, you may purchase new jets from your

local store. Do not attempt to clean the jet mechanically.

Replacing a blocked jet

• Your appliance is ﬁtted with a speciﬁc

size jet to regulate the correct amount of

gas.

• Should the hole in the jet become

blocked, this may result in a small ﬂame

or no ﬂame at all. Do not attempt to clean

the jet with a pin or other such device as

this may damage the oriﬁce, which could

make the appliance unsafe.

• To replace the jet: Remove the fat pan

(Fig. 5). Gently unscrew the burner

assembly (Fig. 6). Remove the three

screws from the heat shield plate

and remove the heat shield (Fig. 7),

taking care not to damage the piezo

electrode. The jet can now be removed

using a suitable spanner (Fig. 8). Do not

use pliers on the jet as this may damage

the jet, making it unusable or impossible

to remove. Screw the new jet into the

valve. Do not over-tighten as this may

damage the jet.

• Reverse the above procedure to re-

assemble the unit.

Fig. 5 Fig. 6

Fig. 8

Jet

Fig. 7

7. Storage

• Always allow the unit to cool down and be cleaned before storing.

• Turn oﬀ the gas supply to the appliance, disconnect and remove the gas supply from the appliance.

• Never store an appliance with the gas supply connected, this is an unsafe practice.

• Store the appliance and gas supply in a well-ventilated area away from combustible material. Storage of cylinders should preferably be

outdoors and must NOT be in a basement.

Piezo

electrode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac Safari Chef 30 - 6540H1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info