Bedienungsanleitung Cadac Skottel Braai 50 - 8309T-13 (Seite 5 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

820004

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

2. Fitting and Changing the Gas Supply

Connecting the gas supply

• Before connecting the appliance to a gas supply, ensure that the rubber seal on the regulator is in position and in good condition.

• Before connecting the hose and regulator to the appliance, check that the appliance control knob (K) is in the “OFF” position (“•” - turn

fully clockwise).

• Carry out this check each time you ﬁt the appliance to a gas cylinder.

• Blow out any dust from the gas supply opening to prevent possible blockage of the jet.

• NOTE! When installing the tailpiece, ensure it is held straight while tightening the tailpiece nut, in order to prevent a possible gas leak. Tighten

with a suitable spanner or hand wheel.

• Fit an approved hose and regulator to the appliance.

• Ensure that the gas supply (gas cylinder/gas cartridge) is ﬁtted in a well-ventilated location away from any source of ignition, such as naked

ﬂames and away from other people.

• Do not twist or pinch the hose. Ensure that it is routed away from the stove body so as to prevent deterioration / damage to the hose

caused by heat.

• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by screwing on hand tight until fully engaged.

• Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). Do not check for leaks with a naked

ﬂame. Use warm soapy water only, applied to the joints and connections of the appliance. Any leakage will show up as bubbles around the

leakage area.

• If you cannot rectify the gas leak do not use the appliance. If you are in doubt, contact your nearest stockist.

Disconnecting and changing the gas supply

• Aer use, turn the appliance control knob to the “OFF” position and close the gas supply.

• When you need to replace your empty cylinder, make sure that the gas is closed at the cylinder valve.

• Do not smoke while changing the cylinder.

• Remove the regulator from the empty cylinder.

• Attach the regulator to the full cylinder, refer to the instructions above on how to connect the gas supply.

• Apply the same care and checking procedures as if ﬁtting a new gas cylinder.

How to check if your gas cylinder is empty

• The easiest way to check if you are low on gas is by picking up your gas cylinder.

• If you think your gas cylinder is feeling a little lighter than you’d like, weighing the bottle is a great way to see how much gas is le. Most

cylinders will have the empty weight stamped on either the neck or foot ring, and if the weight indicated on the stamp and the weight of your

cylinder are the same, you’re out of gas. You can then approximate the amount of gas you have le by the diﬀerence in weight.

• Assemble the tripod stand as per ﬁgure 2a and 2b.

Fig. 2a

Fig. 2b

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac Skottel Braai 50 - 8309T-13 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info