Bedienungsanleitung Cadel Aquos 15 (Seite 39 von 56) (Englisch)

643489

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

AQUOS - IBIS - IDRON

Connect the cables from the external thermostat to points 1-2 of the terminal block on the boiler.

Once the thermostat has been connected one must enable it.

In order to do this, proceed as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows.

• Select by pressing “menu”.

• Scroll once again to “External thermostat” using the arrows.

• Select by pressing “menu”.

• Press the - + buttons.

• Select “On” to activate the external thermostat.

• Press the “menu” button to conrm.

• Press the “esc” button to exit.

13.3 START-UP

Press key 1 (esc) to begin start-up, the control panel displays ON with a ashing ame. When the ame stops

ashing the boiler has reached the “power output” operating mode.

The room temperature set by default is 20°C, if one wishes to change it act as instructed in the adjustments

menu; act likewise to set the heating water temperature and the room fan speed (if envisaged). To activate

external thermostat if any see the relative section.

13.4 POWER OUTPUT

Once the start-up stage is complete the control panel will display ON with a xed ame at level 3. The subsequent

ame modulation at lower or higher powers is managed autonomously and upon reaching the temperatures

set in the “System conguration”.

13.5 PROGRAMMED MODE (TIMER) - MAIN MENU

Setting the current day and time is essential for the proper operation of the timer.

There are six TIMER programmes, for each one the user can decide the start-up and shutdown time as well as the

day of the week in which it is active.

When one or more programmes are active, the panel alternately displays the boiler status and TIMER “n” whereby

“n” is the number relating to the activated timer programmes, separated from each other with a dash

Example:

TIMER 1 Timer programme 1 active.

TIMER 1-4 Timer programmes 1 and 4 active.

TIMER 1-2-3-4-5-6 Timer programmes all active.

EXAMPLE OF PROGRAMMING

With boiler on or off:

access the MENU,

scroll to TIMER with the <> arrows,

press the “Menu” key

the system proposes “P1” (Press the <> keys for the subsequent timers P2,P3, P4, P5, P6)

to activate “P1” press the “Menu” key

press + - and select “ON”

conrm with the “Menu” key

At this point it will propose 00:00 as starting time, with key + - adjust the starting time and press the “menu” key

to conrm.

The next step proposes a shutdown time of 10 minutes above that set for start-up: press the + key and adjust the

shutdown time, conrm with the “menu” key.

Subsequently the system proposes the days of the week in which to activate or deactivate the previously set

timer. With the - or + key highlight with the white background the day in which one wishes to activate the timer

and conrm with the “menu” key. If no day of the week is conrmed as active, in turn the timer programme will

not appear active in the status screen.

Continue to program the following days or press “ESC” to exit. Repeat the procedure to program the other

timers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Aquos 15 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Aquos 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info