Bedienungsanleitung Cadel Eolo (Seite 9 von 40) (Englisch)

694380

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

EOLO - COMFORT 80

8.8 EXTERNAL AIR INLET

Fig. 6 - Direct air inow Fig. 7 - Indirect air inow

LEGEND Fig. 6 page 9|Fig. 7 page 9

1 Room to ventilate

2 Adjacent room

3 External air inlet

4 Cleft under the door

• The room must be endowed with an external air recycling for a good climate in your ambient.

• The air inow from outside to the inner occurs directly, through an opening on the external wall of the room

(see Fig. 6 page 9); otherwise it occurs indirectly by air suction from rooms adjacent to the one to ventilate

(see Fig. 7 page 9).

• Bedrooms, garages, and store of ammable materials are excluded.

• The air inlet should have a total net surface of 80 sqcm

: the aforesaid surface is to widen if inside the room

there are other activated appliances (for example: electric ventilators for foul air suction, cooker hoods, other

stoves, etc...) which depress the environment.

• At switched on appliance it is necessary to check that the pressure fall between the room and the outside

does not exceed 4,0 Pa value: if necessary widen the air inlet (EN 13384).

• The air inlet must be realized at a height close to the oor with an external grid against birds. In such a way it

cannot be obstructed by any object.

• In case of installation with sealed-chamber the air inlet is not necessary.

8.9 CHIMNEY FLUE CONNECTION

Your pellet stove works through a fume draught forced by a fan. It is obligatory to check that all pipes are

realized in compliance with the following regulation on material selection: EN 1856-1, EN 1856-2 e UNI/TS 11278.

All must be effected by specialized personnel or companies as provided by UNI 10683:2012.

• The connection between the appliance and the chimney ue should be short in order to favor the draught

and to avoid condensation in the pipes.

• The fume conduit should be equivalent or longer than the outlet joint ones (Ø 80 mm).

• Some stove models are endowed with a lateral and/or back exhaust. Check that the unused exhaust is

sealed with the plug given with standard equipment.

SYSTEM TYPE Ø80 mm PIPE Ø100 mm PIPE

Minimum vertical length 1,5 mt 2 mt

Maximum length (with 1 union) 6,5 mt 10 mt

Maximum length (with 3 unions) 4,5 mt 8 mt

Maximum number of unions 3 3

Level section (minimum inclination 3%) 2 mt 2 mt

Installation at a height above 1200 m a.s.l. NO Obligatory

• Use a plate pipe for stoves of Ø80 mm or Ø100 mm depending on the type of system and with silicone gaskets.

• It is forbidden to use metal, bre cement or aluminium exible pipes.

• For change of direction it is obligatory always to use a union (with angle > 90°) with inspection plug which

enables an easy periodic cleaning of the pipes.

• Please assure you that after the cleaning the inspection plugs are sealed with its efcient gasket.

• It is forbidden to connect more appliances to the same fume conduit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Eolo Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Eolo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info