Bedienungsanleitung Cadel IDRO PRINCE 30 (Seite 39 von 72) (Englisch)

696857

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

IDRO PRINCE

12-16-23-23 H

O - IDRO PRINCE 30-30 H

O - AQUOS

16-23-23 H

O - IDRON 16-22 AIRTIGHT - MIRA 16-22 -

TESIS 16-23

AIRTIGHT - HIDROFIRE 22.8

7.9 WASHING THE SYSTEM

The connections must be easy to disconnect via pipe unions with swivel fittings.

Install suitable gate valves on the heating system pipes. A safety valve must be installed on the system.

To protect the heating system from harmful corrosion, build-ups or deposits, it is extremely important before installing the ap-

pliance to wash the system in compliance with the UNI 8065 standard (water treatment in heating systems for domestic use),

using appropriate products.

7.10 FILLING THE SYSTEM

To fill the system, the stove may be equipped with a terminal (optional) with a non-return valve (D) to manually fill the heating

system (if there is no terminal, use the filling valve on the main boiler). During this operation, the automatic bleed valve under the

top ensures that any air in the system is expelled.

To allow the valve to bleed, we recommend loosening the grey cap by a turn and leaving the red cap tight (see figure). The filling

pressure when the system is COLD must be 1 bar. During operation, should system pressure drop (due to the gas dissolved in the

water evaporating) below the above indicated minimum value, the user must bring it back to the initial value, using the filling valve.

For proper stove operation when it is HOT, pressure in the boiler must be 1.5 bar.

To monitor system pressure, the terminal (optional) is equipped with a pressure gauge (M).

When filling is complete, always shut off the valve.

It is normal for there to be noises and gurgling until all the air in the system has been expelled.

Fig. 45 - Terminal with lling valve (D) and

pressure gauge (M)

Fig. 46 - Manual bleed valve (located under the

top) (Idro Prince

16-23-23 H2O, Aquos

16-23-23

H2O, Idron 16-22 Airtight, Hidrore 22.8)

Fig. 47 - Manual bleed valve (located under the

top) (Idro Prince

30-30 H2O)

7.11 WATER CHARACTERISTICS

The characteristics of the water used to fill the system are very important to prevent the build-up of mineral salts and the forma-

tion of incrustations along the pipes, in the boiler and in the heat exchangers.

Therefore, please ASK YOUR PLUMBER FOR HIS ADVICE CONCERNING:

Hardness of water circulating in the system, to prevent problems of incrustation and limescale, especially in

the domestic water heat exchanger. (> 25° French).

Installation of a water softener (if water hardness exceeds 25° French).

Filling the system with treated water (demineralised).

Possibly providing an anti-condensation circuit.

Installation of hydraulic shock absorbers to prevent water hammering along the fittings and pipes.

If you have very extensive systems (with a large amount of water) or which require frequent refilling, the installation of water

softening systems.

It should be remembered that incrustations drastically reduce performance due to their extremely low thermal

conductivity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel IDRO PRINCE 30 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel IDRO PRINCE 30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info