Bedienungsanleitung Cadel IDRO PRINCE 30 (Seite 59 von 72) (Englisch)

696857

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

IDRO PRINCE

12-16-23-23 H

O - IDRO PRINCE 30-30 H

O - AQUOS

16-23-23 H

O - IDRON 16-22 AIRTIGHT - MIRA 16-22 -

TESIS 16-23

AIRTIGHT - HIDROFIRE 22.8

12.18 BLACKOUT ABOVE 10” WITH BOILER IN SHUTDOWN STAGE

In the event there is a power cut that lasts MORE THAN 10” with the boiler in the shutdown stage, when the boiler is powered again

it restarts in shutdown mode even if the smoke temperature has fallen under 45°C in the meanwhile. This last stage can be skipped

by pressing key 1 (esc) (it goes into start-up) and by pressing it again (it recognises that the boiler is switched off).

13 RECOMMENDATIONS FOR SAFE USE

ONLY PROPER INSTALLATION AND APPROPRIATELY SERVICING AND CLEANING THE APPLIANCE

CAN ENSURE PROPER OPERATION AND SAFE PRODUCT USE

We wish to inform you that we are aware of cases of malfunctioning domestic pellet heating products, essentially due to improper

installations and inappropriate maintenance.

We wish to ensure you that all our products are extremely safe and certified according to the European reference standards. The

ignition system was tested with extreme care to increase ignition efficiency and prevent any issues even in the worst operating

conditions. In any case, as with any pellet product, our appliances must be installed properly and periodically cleaned and serviced

in order to ensure safe operation. Our research suggests that these malfunctions are essentially due to a combination of part or all

of the following factors:

• Clogged brazier holes or deformed brazier, due to poor maintenance. These conditions can cause delayed ignition, creating an

abnormal production of unburnt gases.

• Insufficient combustion air due to a reduced or clogged air intake duct.

• Using smoke ducts that do not meet the installation standard requirements, such to fail to ensure appropriate draft.

• Partially obstructed chimney due to poor maintenance, such to reduce draft, making ignition difficult.

• Terminal chimney cap not compliant with the instructions manual, thus not suitable to prevent potential backdraft.

• This factor becomes crucial when the product is installed in particularly windy areas, like on the coast.

The combination of one or more of these factors could cause significant malfunctions.

To prevent this from happening, it is essential to ensure the product is installed in compliance with the standards in force.

Furthermore, it is essential to follow these simple rules:

• Every time it is removed for cleaning, the brazier must always be properly repositioned in the work position before using the

product, thoroughly cleaning any residual dirt on the support base.

• Never load pellets into the brazier manually, either before ignition or during operation.

• Any unburnt pellets after a failed ignition must be removed before re-igniting the product. Also make sure it is properly posi-

tioned in its housing and check for normal combustion air intake/smoke extraction.

• If the product repeatedly fails to ignite, we recommend that you stop using it immediately and contact a qualified technician

to check product operation.

Following these instructions is more than enough to ensure normal operation and prevent any issues with the product.

If the above precautions are not respected and there is a pellet overload in the brazier during ignition and subsequent abnormal

smoke generated in the combustion chamber, carefully follow these instructions:

• Do not, for any reason, unplug the product from the electrical mains: this would stop the smoke extraction fan, resulting in

smoke being emitted into the room.

• Pre-emptively open the windows to air any smoke out of the installation room (the chimney may not work normally)

• Do not open the fire door, as this would compromise normal operation of the smoke exhaust system to the chimney.

• Simply switch off the stove using the on/off button on the control panel (not the rear button of the power supply plug!) and

move away from the product as you wait for the smoke to clear completely.

• Before any attempts to reignite the product, thoroughly clean the brazier and its air passage holes from build-up and any

unburnt pellets; reposition the brazier in its housing, removing any residue from its support base. If the product repeatedly fails

to ignite, we recommend that you stop using it immediately and contact a qualified technician to check product and chimney

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel IDRO PRINCE 30 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel IDRO PRINCE 30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info