Bedienungsanleitung Cadel IDRON 16-22 AIRTIGHT (Seite 18 von 40) (Englisch)

815161

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

IDROSTUFE

h - Pump On T

This menu item allows to adjust the pump activation temperature.

To select the Pump On T function act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to confirm.

• Scroll to “Pump On T” using the arrows.

• Press “menu” to confirm.

• Modify the °C with the + - keys.

• Press “menu” to confirm and “esc” to exit

i - Auxiliary boiler

An additional (optional) module must be installed to allow an auxiliary boiler to be switched on should the stove be off or in alarm

conditions. By default, this function is disabled; if necessary, activate it through the settings menu.

j - Pellet Recipe

This function is for adapting the stove to the pellets that are being used. In fact, as there are several types of pellets on the market,

boiler operation is extremely variable depending on the fuel quality. In the event the pellets tend to clog the brazier due to an

excessive load of fuel or in the event the flame is always high even at low powers and, vice versa if the flame is low one can decre-

ase/increase the amount of pellets in the brazier:

The available values are:

-3 = Decrease by 30% compared to factory settings.

-2 = Decrease by 20% compared to factory settings.

-1 = Decrease by 10% compared to factory settings.

0 = No variation.

1 = Increase by 5% compared to factory settings.

2 = Increase by 10% compared to factory settings.

3 = Increase by 15% compared to factory settings.

To change the recipe act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to confirm.

• Scroll to “Pellet recipe” using the arrows.

• Press “menu” to confirm.

• Modify the % with the + - keys.

• Press “menu” to confirm and “esc” to exit

k - Smoke rpm % ventilation

If the installation presents difficulties for smoke evacuation (no draught or no pressure in the duct), the smoke and ash expulsion

speed can be increased. This change resolves all the potential problems related to pellets clogging in the brazier and deposits

forming at the bottom of the brazier itself caused by poor quality fuel or fuel that produces a lot of ashes. The values available are

from -30% to +50% with variations of 10 percentage points at a time. The variation in negative can be used in case the flame is

too low.

To change the parameter act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to confirm.

• Scroll to “Smoke rpm variation” using the arrows.

• Press “menu” to confirm.

• Modify the % with the + - keys.

• Press “menu” to confirm and “esc” to exit

l - Maximum power

It allows to set the maximum flame limit at which the boiler can operate to reach the set temperature target.

To change the power act as follows:

• Press the “menu” button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel IDRON 16-22 AIRTIGHT Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info