Bedienungsanleitung Cadel Lean3 Plus (Seite 33 von 48) (Englisch)

694402

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WALL

PLUS - LEAN

PLUS - MOON - TILE

PLUS

(I can therefore delay the shutdown for up to a maximum of 23 hours and 50 minutes).

Fig. 63 - Sleep

If the SLEEP function is active with the TIMER active the rst has priority over the latter, therefore the boiler will not

switch off at the time set on the timer but instead by the time established by the sleep function, even if later than

the time set on the timer.

12.17 PELLETS RECIPE (SEE SECTION J SETTINGS MENU PAGE 27)

This function is for adapting the stove to the pellets that are being used. In fact, as there are several types of

pellets on the market, boiler operation is extremely variable depending on the fuel quality. In the event the

pellets tend to clog the brazier due to an excessive load of fuel or in the event the ame is always high even at

low powers and, vice versa if the ame is low one can decrease/increase the amount of pellets in the brazier:

The available values are:

-30= 30% reduction with respect to the default setting.

-25= 25% reduction with respect to the default setting.

-20= 20% reduction with respect to the default setting.

-15 = 15% reduction with respect to the default setting.

-10= 10% reduction with respect to the default setting.

-5= 5% reduction with respect to the default setting.

0= No variation.

+5= 5% increase with respect to the default setting.

+10 = 10% increase with respect to the default setting.

+15 = 15% increase with respect to the default setting.

12.18 SMOKE RPM VARIATION (SEE SECTION I SETTINGS MENU PAGE 27)

If the installation presents difculties for smoke evacuation (no draught or no pressure in the duct), the smoke

and ash expulsion speed can be increased. This change resolves all the potential problems related to pellets

clogging in the brazier and deposits forming at the bottom of the brazier itself caused by poor quality fuel or fuel

that produces a lot of ashes. The values available are from -27% to +27% with variations of 3 points at a time. The

variation in negative can be used in case the ame is too low.

12.19 CHIMNEY SWEEP FUNCTION (FOR MAINTENANCE TECHNICIANS ONLY) - SEE SECTION K

SETTINGS MENU PAGE 27

This function can be activated only when the boiler is on and with power output and heating operation power

with parameters P5, with fan (if present) in V5. Any loading/smoke ventilation percentage corrections must

be taken into account. This status lasts 20 minutes, the countdown is displayed on the panel. At any time the

technician can interrupt this stage by quickly pressing the on/off key.

12.20 PELLET SUPPLY

Fig. 64 - Wrong opening of the pellets bag Fig. 65 - Right opening of the pellets bag

It is necessary to avoid to ll the hopper with the pellet when the stove is running.

• Do not get the bag of pellet in contact with hot stove surfaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Lean3 Plus Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Lean3 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info