Bedienungsanleitung Cadel Pretty (Seite 25 von 40) (Englisch)

643577

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

MIRIAM - MARY - PRETTY - VERVE - CRISTAL

12.5 STOVE ADJUSTMENT

The stove is adjusted according to the chimney ue and used pellets datas, as per technical characteristics (see

FEATURES page 39). If the datas do not correspond, the authorized technician can adjust the stove.

• If the pellet is small in size and with a greater caloric power, (for example: encrusted burning pot), the pellet

drop must be decreased from the menu "FLAME SETTING", press P3 "PELLET TYPE", press P3 again "PELLET LOAD"

and with P2 key decrease the pellet quantity from -1 (which is -2%) till -9 (which is -18%).

• If the chimney ue has a lower draught (for example: weak ame, sooty glass) the revolutions of the geared

motor must be increased from the menu "FLAME SETTING", press P5 "CHIMNEY TYPE", press P3 "FUME-EXH

CHIMNEY" and with P1 key increase the fume fan revolutions from +1 (which is +5%) till +9 (which is +30%).

• If the chimney ue has a greater draught (for example: because of pellets fall on the burning pot) decrease

the fume fan revolutions from -1 to -9.

Pay attention if the value is positive or negative..

12.6 AIR REGULATOR

The stove is provided with a back air regulator and must have the following parameters (written also on the back

of the stove):

Fig. 39 - Air regulator

• Air regulator entrance 12 mm to nominal power with a chimney ue of 11 Pa.

12.7 FAILED IGNITION

If the pellets do not burn, the failed ignition will be indicated by the alarm "FAILED IGNITION".

• If the room temperature is lower than 10°C, the plug is not able to bear the ignition stage. To support it please

insert some pellets in the burning pot and a piece of burning relighter igniter material on the pellets (for

example relighters cubes).

• Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difcult and create

dense white smoke which is harmful to health and can cause explosions on the combustion chamber. It is

therefore necessary not to stand in front of the stove during ignition stage if dense white smoke is present.

If after some months the ame appears weak and/or orange colored or the glass tends

to blackens and the burning pot to become encrusted, clean the stove, clean the fume

conduit and the chimney ue.

12.8 POWER FAILURE

• After a black-out lower than 5 seconds, the stove turns back to the power which was settled.

• After a black-out of more than 5 seconds, the stove enters the "COOLING WAIT" phase. Completed this

phase, it starts automatically up with the different phases (see START UP page 24).

12.9 TEMPERATURE SETTING

• To modify the ambient temperature it is sufcient to press P1 and P2 keys according to the desired temperature

inside the menu "SET TEMP ROOM".

• To see the set temperature, press once P1 key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Pretty Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Pretty

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info