Bedienungsanleitung Cadel SFERA 3 (Seite 24 von 48) (Englisch)

643756

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

VEGA - SIRE

PLUS - DOGE

PLUS - SFERA

- SFERA

PLUS - PRINCE

- PRINCE

PLUS - GLOBE - TREND - ELISE

PLUS

• Fit the pipe with insulating material if it passes through a cold wall.

• The outlet must be protected by a grid with wide mesh and a minimum total surface area of 40 cm

• If the pipes used are longer than 6 mt, the air capacity ranges from a minimum of 58 m

/h to a maximum of

883 m

/h and the temperature from 65°C to 99°C. (These values refer to the laboratory used for the tests. The

room where the stove is installed may register different values both in terms of capacity and temperature).

• If you wish to increase air capacity, install at the end of the pipe a small wall-mounted fan with a capacity

exceeding 130 m

/h. The installation must be carried out by an authorised technician.

• According to the factory parameters, 1/2 of the generated heat is conveyed into the room where the stove

is installed, while the remaining 1/2 are conveyed through the left ducting pipe system.

• Balance heat output with air capacity to obtain the best performance (see FAN ADJUSTMENT page 28).

The operation above must be carried out by an authorised technician.

11.13 USING THE STOVE WITHOUT DUCTING

The stove can be used without ducting the air to other environments.

In this case, assemble the environment diffuser in the stove's rear (see Fig. 49 page 24).

Fig. 49 - Diffuser assembly

USE

12.1 INTRODUCTION

To have the best performance with the lowest consumption please follow the here descripted instructions.

• The lightning of the pellets occurs very easily if the installation is correct and if the chimney ue is efcient.

• Switch on the stove at Power 1 for at least 2 hours in order to enable the materials which make up the boiler

and the replace to adjust the inner springing stress.

• By using the stove the varnish inside the combustion chamber could be subjected to alterations. This

occurrence can be attributed to different reasons: an excessive stove overheating, the presence of chemical

agents in bad quality pellets, bad chimney draught, etc. Therefore varnish endurance in the combustion

chamber cannot be guarantee.

Oily plant waste and lacquers can cause smells and smoke during the rst working hours: it

is advisable to ventilate the room because they could be noxious to people and animals.

Set values from 1 to 5 are dened by the manufacturer and they can be changed only by

an authorized technician.

12.2 CONTROL PANEL

PANEL ELEMENT DESCRIPTION

P1 and P2: when in set temperature mode, they are useful to increase or decrease the

thermostat value from min. 6°C to max 40°C. Keeping pressed P2 key it is possible to see

the fume temperature at the exhaust. Both have programming functions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel SFERA 3 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel SFERA 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info