Bedienungsanleitung Cadel SWEET 3-7- 7.0 (Seite 17 von 40) (Englisch)

814920

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Stufe a pellet

8.8 SWITCH OFF ON PANEL: OFF WITH FLASHING FLAME

If the shutdown key is pressed or if there is an alarm signal, the boiler goes into the thermal shutdown phase which entails the

automatic execution of the following stages:

• Pellet loading is stopped.

• The room fan continues to operate until the requested temperature is reached.

• The flue fan is set to its highest value, which it keeps until the requested temperature is reached, plus a safety time of 10

additional minutes. After that, if the fume temperature has decreased below the switch off threshold, it stops, otherwise the

cooling process goes on.

• If the stove has switched off normally, but owing to thermal inertia, the fume temperature goes over the threshold again, the

switch off process is reactivated until the temperature decreases again.

8.9 POWER FAILURE

• After a black-out lower than 10 seconds, the stove turns back to the power which was settled.

• After a black-out of more than 10 seconds, the stove enters the during shutdown. Completed this phase, it starts automatically

up with the different phases.

8.10 ADJUSTMENTS MENU

To access the adjustments menu act as follows:

• Press the + - keys

• Scroll with the <> arrows and select “Set Room T ” or “Air Fan Speed 1” or “Air Fan Speed 2” or “Comfort Mode” or "Fire"

• Press “menu” to access the selected option.

• Modify with the + - keys.

• Press “menu” to confirm and “esc” to exit.

Set Room T. - this function allows setting the desired temperature in the room where the stove is installed, starting from a mi-

nimum of 5°C up to a maximum of 35°C. When this condition is met, the stove reaches the minimum consumption values (flame

and hot air fan speed at minimum values) and then goes back to theset values when the ambient temperature goes below the set

threshold (see Fig. 13).

Fig. 13 - Display

Note: The full stop to the right of the ambient temperature shown in the control panel display (upper right) indicates the half

degree (e.g. 23.° means 23.5°C).

Air Fan Speed 1 - this function allows selecting the desired speed for the ambient fans from 1 to 5 or A. A means automatic,

ventilation depends on power, recommended setting (see Fig. 14).

Air Fan Speed 2 - (ONLY FOR STOVES WITH DUCTING) this function allows selecting the desired speed for the DUCTING fans from

1 to 5 or A. A means automatic, ventilation depends on power, recommended setting (see Fig. 15).

Air Fan Speed. 3 - (ONLY FOR STOVES WITH DUCTING) this function allows selecting the desired speed for the DUCTING fans from

1 to 5 or A. A means automatic, ventilation depends on power, recommended setting (see Fig. 16).

Fig. 14 - Display Fig. 15 - Display Fig. 16 - Display

With function “1” or "2" or "3" or "4" or "5" the fan is forced to work at the selected output. (For example: by setting “3”, even if the

fan is set to heat output 5 it will work as if set to heat output “3”, etc.).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel SWEET 3-7- 7.0 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel SWEET 3-7- 7.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info