Bedienungsanleitung Cadel Tabla (Seite 16 von 36) (Englisch)

694391

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

GRACE - SPIRIT 5KW

l - Technical Menu

To access the technical menu one must contact an assistance centre as one needs a password to enter.

8.5 INFO MENU

• Product Type

• Firmware Version

• Software info

• Total hrs.

• Ignition N.

• Rpm Smoke Fan

• Smoke Temp.

• Air Fan Voltage

• Screw Loading

• Fire

8.6 IGNITION OF THE STOVE

We remind you that the first ignition must be carried out by a specialized and authorixed technician who will check that all is

installed in compliance with current regulations and checks the efficiency.

• If inside the combustion chamber there are booklets, manuals, etc..., remove them.

• Check if the door is correctly closed.

• Check if the stove is correctly inserted in the electric socket.

• Before switching the stove on, assure you the burning pot is clean.

• To start the stove, keep the P1 button pressed until the ON sign and a flashing flame to its side appear. The ignition resistance

pre-heating starts. After some seconds the feed screw loads pellets and the resistance pre-heating continues. When the tem-

perature is high enough (after about 5-8 minutes), ignition is considered to be completed.

• Once the ignition step is complete, the stove moves into operating mode and shows the selected heat output, the ambient

temperature and the big flame (see Fig. 11).

• If the ambient temperature value exceeds the limit set on the button panel in the temperature set, the heat output is brought

to its lowest value and the small flame is shown (see Fig. 12). When the ambient temperature decreases below the set tem-

perature, the stove goes back to the set output.

Fig. 11 - Big ame Fig. 12 - Small ame

8.7 FAILED IGNITION

If pellets should not ignite, the lack of ignition will be signalled by the A01 "No Ignition" warning.

If the ambient temperature is below 5°C, the resistance may not heat up enough to guarantee the pallet ignition. In this case,

remove the unburned pellets from the burning pot and restart ignition.

Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difficult and create dense white smoke

which is harmful to health and can cause explosions on the combustion chamber. It is therefore necessary not to stand in front of

the stove during ignition stage if dense white smoke is present.

If after some months the flame appears weak and/or orange colored or the glass tends to blackens and the

burning pot to become encrusted, clean the stove, clean the fume conduit and the chimney flue.

ATTENTION!

Make sure pellets and ash have not accumulated in the brazier due to failed ignition. If the brazier is not clea-

ned before reattempting, there is the risk of further failed ignitions and even explosions in some cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Tabla Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Tabla

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info