Bedienungsanleitung Cadel Tabla (Seite 21 von 36) (Englisch)

694391

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

GRACE - SPIRIT 5KW

8.17 PELLETS RECIPE SEE SECTION H SETTINGS MENU A PAG. 13

Changes to be made with the support of the authorised technician.

Activates only with the Easy Set function disabled, "SET: 0" !

This function is for adapting the stove to the pellets that are being used. In fact, as there are several types of pellets on the market,

boiler operation is extremely variable depending on the fuel quality. In the event the pellets tend to clog the brazier due to an

excessive load of fuel or in the event the flame is always high even at low powers and, vice versa if the flame is low one can decre-

ase/increase the amount of pellets in the brazier:

The available values are:

-30= 30% reduction with respect to the default setting.

-25= 25% reduction with respect to the default setting.

-20= 20% reduction with respect to the default setting.

-15 = 15% reduction with respect to the default setting.

-10= 10% reduction with respect to the default setting.

-5= 5% reduction with respect to the default setting.

0= No variation.

+5= 5% increase with respect to the default setting.

+10 = 10% increase with respect to the default setting.

+15 = 15% increase with respect to the default setting.

8.18 SMOKE RPM VARIATION SEE SECTION I SETTINGS MENU A PAG. 13

Changes to be made with the support of the authorised technician.

Activates only with the Easy Set function disabled, "SET: 0" !

If the installation presents difficulties for smoke evacuation (no draught or no pressure in the duct), the smoke and ash expulsion

speed can be increased. This change resolves all the potential problems related to pellets clogging in the brazier and deposits

forming at the bottom of the brazier itself caused by poor quality fuel or fuel that produces a lot of ashes. The values available are

from -27% to +27% with variations of 3 points at a time. The variation in negative can be used in case the flame is too low.

8.19 CHIMNEY SWEEP FUNCTION FOR MAINTENANCE TECHNICIANS ONLY  SEE SECTION K SET

TINGS MENU A PAG. 13

This function can be activated only when the boiler is on and with power output and heating operation power with parameters

P5, with fan (if present) in V5. Any loading/smoke ventilation percentage corrections must be taken into account. This status lasts

20 minutes, the countdown is displayed on the panel. At any time the technician can interrupt this stage by quickly pressing the

on/off key.

9 FUEL

9.1 FUEL

• Use top-quality pellets because they have influence in the calorific value and in ash remains.

• Not adequate pellets cause a bad combustion, a frequent burning pot obstruction and exhaust conduits obstruction. Further it

decreases the calorific value, soils the glass and increases consumptions and ash and unburnt granules quantity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Tabla Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Tabla

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info