Bedienungsanleitung Cadel Tabla (Seite 7 von 32) (Englisch)

694391

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

GRACE - SPIRIT 5 - ATRIUM 5 - SOLO - ROXY - TABLA - MADISON 5

Fig. 5 - Anti-wind chimney pots Fig. 6 - Reux area

3.6 MAINTENANCE

• The fumes extraction pipes (fumes conduit + chimney flue + chimney pot) must always be cleaned, scrubbed and checked

by an expert stove-repairer, in compliance with current regulations, with the instructions of the stove-manufacturer and the

directives of your insurance company.

• In case of doubts, please follow the most restrictive regulations.

• Have your chimney flue and chimney pot checked and cleaned by an expert chimney sweep at least once a week. The chimney

sweep has to release a written declaration about the security of the system.

• Not cleaning compromise safety.

4 COMBUSTION AIR

4.1 AIR INLET

It is mandatory to provide an adequate external air inlet that supplies the combustion air required for the product to work properly.

The flow of air between the outside and the installation room can take place with a free air inlet or by channelling the air directly

to the outside (***).

The free air inlet must be:

• be made at floor level and in any case not higher than the height of the appliance;

• always be protected with an outer grille and in such a way that it cannot be obstructed by any object;

• have a minimum total free area of 80 cm2 (net of the grille);

The presence of other suction devices (e.g.: vmc, electric fan for stale air extraction, kitchen hood, other stoves, etc.), in the same

room,or in communicating rooms of the same housing unit, could cause negative pressure in the room. In this case, with the

exception of sealed installations, one must verify that, with all the equipment on, no more than 4 Pa of negative pressure is created

inside the installation room with respect to the outside. If necessary, increase the air inlet section.

It is possible to duct the air required for combustion to the outside by connecting the external air inlet directly with the combustion

air inlet which is usually found on the back of the appliance.

The external ducted air vents must be:

• made close to the floor and anyway not higher than the appliance

• protected by a grille that guarantees a clear surface equal to the cross-section of the duct and made so that it cannot be ob-

structed by any object

• The air vent can be made directly on a wall of the installation room communicating with the outside, or indirectly in adjacent

rooms that permanently communicate with the installation room, according to that set forth by standards in force.

The duct must comply with the following dimensions (each 90° bend is equivalent to one linear metre):

(***) In the event the combustion air is ducted on unsealed products, still verify that no more than 4 Pa of negative pressure is created

inside the installation room with respect to the outside, otherwise provide for an additional air intake in the room.

Below 15 kW:

Air duct diameter Maximum length (smooth duct) Maximum length (corrugated duct)

50 mm 2 m 1 m

60 mm 3 m 2 m

80 mm 7 m 4 m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Tabla Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Tabla

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info