Bedienungsanleitung Cadel ZEN AIRTIGHT - 2018 (Seite 19 von 36) (Englisch)

696355

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ZEFIRO

- ZEN AIRTIGHT

-30= 30% reduction with respect to the default setting.

-25= 25% reduction with respect to the default setting.

-20= 20% reduction with respect to the default setting.

-15 = 15% reduction with respect to the default setting.

-10= 10% reduction with respect to the default setting.

-5= 5% reduction with respect to the default setting.

0= No variation.

+5= 5% increase with respect to the default setting.

+10 = 10% increase with respect to the default setting.

+15 = 15% increase with respect to the default setting.

8.17 SMOKE RPM VARIATION SEE SECTION I SETTINGS MENU A PAG. 7

If the installation presents difficulties for smoke evacuation (no draught or no pressure in the duct), the smoke and ash expulsion

speed can be increased. This change resolves all the potential problems related to pellets clogging in the brazier and deposits

forming at the bottom of the brazier itself caused by poor quality fuel or fuel that produces a lot of ashes. The values available are

from -27% to +27% with variations of 3 points at a time. The variation in negative can be used in case the flame is too low.

8.18 CHIMNEY SWEEP FUNCTION FOR MAINTENANCE TECHNICIANS ONLY  SEE SECTION K SET

TINGS MENU A PAG. 7

This function can be activated only when the boiler is on and with power output and heating operation power with parameters P5,

with fan (if present) in V5. Any loading/smoke ventilation percentage corrections must be taken into account. This status lasts 20 mi-

nutes, the countdown is displayed on the panel. At any time the technician can interrupt this stage by quickly pressing the on/off key.

8.19 PELLET RESERVE ENABLING FUNCTION

The appliance is equipped with a software system that warns when the pellet is about to end.

• Message on display “RISERVA PELLET” (PELLET RESERVE), the appliance goes into energy saving and goes to power P1.

After having filled the pellet tank, press key 3 to reset the “PELLET RESERVE” and ensure that the product can reach the set power.

The duration (in minutes) of the “PELLET RESERVE” is indicated at the top of the display. Every 3’ an acoustic warning (beep) remin-

ds to reload the pellet tank.

Fig. 15 - Pallet Reserve

Unsuitable pellet causes bad combustion and may not correctly operate the “PELLET RESERVE” function.

8.20 COMFORT MODE FUNCTION

“COMFORT MODE” this function allows activating-deactivating the fans at power 1.

The Comfort Mode option can ONLY be excluded for ducted stoves.

8.21 LOAD TIMEOUT AND PELLET OPERATION TIMER FUNCTION

The loading system stops when the tank door is opened.

“LOAD TIME-OUT”: the control unit is equipped with a timer that acoustically warns (with 3 beeps) that the load time available is

over.

If the user requires more time to finish loading the tank, after the acoustic signal, he/she must quickly close the tank cover and

wait 5-6 seconds. In this way the timer resets and the screw starts to let the pellet down again.

After those 5-6 seconds, open the tank lid again and proceed to load the pellet. During this operation, check that the flame is

present on the brazier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel ZEN AIRTIGHT - 2018 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel ZEN AIRTIGHT - 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info