Bedienungsanleitung Caldera Paradise - serie 2020 (Seite 33 von 44) (Englisch)

784916

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 30 Installation

InStallatIon

SITE PREPARATION

You probably have a spot picked out for your new spa, whether it’s

indoors or outdoors, on a patio or on a deck. Please make sure you

check the following:

• Always put your spa on a structurally sound, level surface. A

filled spa can weigh a great deal. Make certain that the location

you choose can support the weight of your filled spa.

• Don’t forget to level your spa before filling it. (See the Spa

Leveling Preparation.)

• Locate your equipment compartment, which houses all of the

electrical components, in a place where water will drain away

from it. Allowing water into the equipment compartment can

damage the electronics, or may result in tripping your house’s

circuit breaker.

• Leave yourself easy access to the circuit breakers in the

subpanel.

• Leave access to the equipment compartment for periodic spa

care and maintenance.

WARNING: Damage to the spa’s equipment compartment

components or internal plumbing as a result of rodent

infestation is NOT covered under your warranty!

OUTDOOR AND PATIO INSTALLATION

No matter where you install your new spa, it’s important that you have

a solid foundation to support it. Structural damage to the spa, resulting

from incorrect installation, or placement on an inadequate foundation, is

not covered under the spa’s limited warranty.

If you install the spa outdoors, we recommend a reinforced concrete pad

at least four inches thick. The reinforcing rod or mesh in the pad should

be attached to a bond wire.

DECK INSTALLATION

To be certain your deck can support your spa, you must know the

deck’s maximum load capacity. Consult a qualified building contractor

or structural engineer. To find the weight of your spa, its contents and

occupants, refer to the Spa Specification chart on back cover. This

weight per square foot must not exceed the structure’s rated capacity, or

serious structural damage could result.

INDOOR/BASEMENT INSTALLATION

Be aware of some special requirements if you place your spa indoors.

Water will accumulate around the spa, so flooring materials must

provide a good grip when wet. Proper drainage is essential to prevent

a build-up of water around the spa. When building a new room for the

spa it is recommended that a floor drain be installed. The humidity will

naturally increase with the spa indoors. Water may get into woodwork

and produce dry rot, mildew, or other problems. Check for airborne

moisture’s effects on exposed wood, paper, etc. in the room. To minimize

these effects, it is best to provide plenty of ventilation to the spa area. An

architect can help to determine if more ventilation must be installed.

CALDERA spas are equipped with a jet pump shroud to remove

excessive heat from the equipment compartment. Find this vent and be

sure the vent is not blocked by anything, including carpeting.

Your CALDERA dealer can help you with local information such as

zoning regulations and building codes.

WARNING: Please keep the area around your spa well ventilated

when it is installed indoors or in a confined area.

Inadequate ventilation around the spa could cause a build-up of a

higher-than-normal concentration of spa chemicals and/or bacterial

fragments. These dispersed spa chemicals and/or bacterial fragments

can be inhaled, and may result in breathing difficulties or lung damage

in certain people suffering from a compromised immune system

or respiratory infection. If you or other bathers are affected by this

condition, please seek medical attention as soon as possible.

In addition to the above, properly clean and maintain your spa as follows:

• Follow all procedures in this owner’s manual and printed

instructions on all water care (chemical) products packaging.

• Test the water regularly to ensure proper levels of sanitizers,

pH, and other water care requirements.

• Drain, clean, and refill your spa with fresh water on a regular

schedule, and in accordance with this owner’s manual.

• Clean the filter at least once per month.

• Check to make sure you have proper circulation throughout

your spa water system.

• Have spa users bathe before entering the spa water.

SPA LEVELING PREPARATION

Concrete sloped at 1.5 cm per 3 m (.5" per 10') is preferred so that rain

water and water spillover will run off and not puddle underneath the spa

(water under the spa for long periods of time may cause the wood to

deteriorate). Other options are brick, stepping stone, or blocks.

It is important to note that soft surfaces, even when stepping stones are

used to evenly distribute the weight of the spa, will have a tendency to

settle, thus resulting in an unleveled spa.

NOTE: Placing the spa on grass or dirt may increase the amount of

debris which is inadvertently brought into the spa water and may cause

harm to your equipment as well as the spa surface, which is not covered

under warranty.

Slope 1.5 cm per 3 m for proper drainage.

3 m

1.5 cm

Stepping stones or brick may settle

causing the spa to be unlevel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caldera Paradise - serie 2020 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Paradise - serie 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info