Bedienungsanleitung Caldera Paradise - serie 2021 (Seite 40 von 44) (Englisch)

784915

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 37

ServIce InformatIon

GENERAL INFORMATION

Your CALDERA spa has been designed to provide years of trouble-

free use. As with any appliance, problems may occasionally occur that

require the expertise of a qualified service person. Though such simple

repairs as resetting a RCD breaker, or resetting a high limit thermostat

may not require a service call, they may indicate that a more serious

condition exists. These conditions may require an experienced service

person. Before calling for service, please refer to the Troubleshooting

Guide. Always retain your original sales receipt for future reference.

RCD AND HIGH LIMIT THERMOSTAT

If your spa fails to operate at any time, first check the power supply to

the spa.

Check each of the RCD breakers in the subpanel. If a RCD has tripped,

reset it. If it will not reset, this may be an indication of a ground fault

(short circuit) within the electrical components. Contact an Authorized

Service Technician for a complete diagnosis.

If upon checking the RCD’s you find that they have not tripped, check

the house breaker panel and ensure the main breaker for the electrical

circuit supplying the spa has not tripped. If it has, this is an indication

that the circuit was either overloaded or a ground fault exists between

the breaker panel and the spa receptacle or subpanel. Contact a

qualified electrician.

If upon checking the main house breaker and spa RCD’s you find no

failures, check the high limit thermostat. To check it, simply turn off

power to the spa for 30 seconds. This will automatically reset the high

limit thermostat if it has tripped. If the spa energizes once you turn the

power back on, this indicates reduced water flow through the heating

system. Tripping of the high limit thermostat is normally a result of

one or a combination of these problems. 1) clogged filter cartridge(s),

2) blockage within the system plumbing, 3) a non-functioning heater

circulation pump, 4) power was not disconnected from the spa before it

was drained, 5) an air lock in the plumbing lines. (The Power Indicator

on the front of the spa’s control panel will also be blinking if the high limit

thermostat circuit has tripped.)

If the spa does not function after tripping and resetting the RCD’s or

resetting the high limit thermostat, then the problem should be referred

to an Authorized Service Technician. Refer to the Troubleshooting Guide

for additional service information.

HEATER AND INTEGRATED

PRESSURE SWITCH

Watkins Wellness unconditionally warrants the heater against any failure

that would require replacement. This warranty’s duration is equal to

the time period identified in the Heater Warranty. This warranty defines

unconditional as warranty coverage without exception provided that the

component has failed to operate properly within the spa’s system. This

means that conditions that would normally invalidate the limited

warranty, such as water chemistry damage, do not apply to the heater.

It is important to note that the heater is protected by both the heater high

limit thermostat circuit and the integrated pressure switch. The causes of

heater high limit tripping are discussed in the previous section.

If the spa is not heating, the red and green lights are blinking, but

the pump and light are operating, then the pressure switch may be

open. Opening of the pressure switch is normally a result of one or a

combination of these problems:

1. A clogged filter cartridge

2. Blockage within the system plumbing

3. Power was not disconnected to the spa before it was drained

4. An air lock in the plumbing lines

5. Circulation pump not properly working

Once the problem has been identified and corrected the pressure switch

will close which will energize the heater.

CIRCULATION PUMP AND

CIRCULATION PUMP THERMAL

CUT-OFF

The circulation pump is a dedicated, water cooled, energy efficient, quiet

pump that provides continuous filtration for the spa. Since the pump is

water cooled, it is equipped with a thermal cut-off to prevent the pump

from being damaged by running hot when water is not present.

Reset the circulation pump’s thermal cut-off by disconnecting power to

the spa and allowing the pump to cool.

Tripping of the thermal cut-off is normally the result of one or a

combination of these problems: 1) clogged filter cartridge(s), 2) blockage

within the system plumbing, 3) power was not disconnected to the spa

before it was drained, or 4) an air lock in the plumbing lines. Once the

problem has been identified and corrected the pump thermal cut-off will

be able to be reset which will allow it to operate normally.

MISCELLANEOUS SERVICE

INFORMATION

The control and high-limit thermostats are equipped with electronic

sensors that are connected to the spa’s plumbing. Never cut or kink the

wires that connect the sensors to the thermostats within the control box.

The jet pump is equipped with a thermal overload cutoff switch that is

designed to protect the pump from overheating. If the pump shuts itself

off in an older spa, it could indicate failure of the pump motor bearings. If

the pump shuts itself off in a new spa, it is usually the result of one or a

combination of the following factors:

• Thermal overload: Although mass-produced, not all thermal overload

cutoffs are exactly the same. Some are more sensitive than others and

will shut the pump off at lower temperatures.

• High temperature: All CALDERA spa models are equipped with a jet

pump shroud that vents the heat generated by the pump motor to the

outside of the equipment compartment, and back into the spa water. If

the vent is blocked by masonry, grass or debris, overheating of the jet

pump may occur. Once the pump motor has cooled sufficiently and any

blockage has been removed from the vent opening, the jet pump can

be restarted.

• Friction: Sometimes the moving parts of a new pump are tight enough

to cause heat build-up due to friction. After a normal break-in period,

the pump will run cooler.

• Improper wiring: If the spa is connected with an extension cord, and/

or the house wiring is undersized, the pump may starve for voltage and

therefore may draw more amperage and generate excessive heat.

• If the pump is shutting down due to excessive heat, make sure the

equipment compartment has adequate ventilation. The air gap at the

bottom must not be blocked. Should your jet pump continue to shut off

after short periods of use, contact a qualified service technician.

Service Information

Caldera Paradise - serie 2021 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Paradise - serie 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info