Bedienungsanleitung Caldera Utopia - serie 2019 (Seite 10 von 44) (Englisch)

784912

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 7

Getting Started

2. AFTER THE SPA HAS BEEN FILLED with water and the

equipment compartment door is secured, power must be applied to

the spa.

• FIRST activate power to the subpanel from the main house panel.

• NEXT open the door of the electrical subpanel and reset the

GFCI/RCD breaker.

• FINALLY, close and secure the subpanel door.

3. TO CHECK THE OPERATION OF THE JET SYSTEM and to purge

any remaining air from the heating system complete the following

steps:

• Press the

JETS

OFF

icon on the Jet screen for each pump to place

the jet pumps on High.

• Once the jet system is fully operational (as indicated by strong,

non-surging jets), priming of the spa is complete

• To turn off the jets, press

the on the jet screen

to turn all

functions off simultaneously.

• If you do not feel a steady stream of water from your jets,

refer to the instructions for priming the pump in the SPA

TROUBLESHOOTING section.

IMPORTANT: Be sure that the diverter is in the middle position.

4. SET THE TEMPERATURE CONTROL to the desired temperature

between 38°C and 40°C, then place the spa cover on the spa and

allow the water temperature to stabilize (approximately 24 hours).

Make sure you secure the cover in place using the cover locks.

Periodically check the spa water temperature. When the water

temperature climbs above 32°C, proceed to the next step. The spa

temperature is pre-programmed to reach 39°C, and will normally do

so within 18 to 24 hours. You may change the water temperature by

pressing the temperature on the home screen, then press the



the screen to raise the temperature, or ▼ to lower the temperature.

After a few hours, the water temperature will remain within 1.5°C of

your selected temperature.

5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust

Total Alkalinity (TA) to 40-120 ppm, Calcium Hardness between

75-150 ppm, then spa water pH to between 7.2 and 7.8. These

procedures are listed in the “Water Quality and Maintenance”

section.

OPERATION NOTE: Adjusting the Total Alkalinity as the first step is

important, as out-of balance TA will affect your ability to adjust the pH

correctly and will prevent the sanitizer from operating effectively.

When using the FRESHWATER Salt system the Calcium Hardness

must be between 25 - 75 ppm, if hardness is above 75 ppm use

VANISHING ACT (see pg. 11).

IMPORTANT: Activate the Clean cycle (Press on the home

screen then Start) before adding spa water chemicals directly into

the filter compartment. Make sure all diverter valves are set to the

middle position.

6. SUPERCHLORINATE THE SPA WATER by adding 1½ teaspoons

of chlorine (sodium dichlor) per 950 liters of spa water, then activate

the Clean cycle.

7. TEST THE SPA WATER FOR CHLORINE RESIDUAL. If the

residual is between 3 and 5 ppm on the test strips, go on to the next

step. If the residual is less than 3 ppm, activate the Clean cycle, add

chlorine as needed and then retest.

WARNING: High sanitizer levels can cause discomfort to the user’s

eyes, lungs and s kin. Always allow the sanitizer level to fall to the

recommended range before using the spa.

8. RECHECK the Total Alkalinity (TA) 40-120 ppm, Calcium Hardness

between 75-150 ppm, then spa water pH between 7.2 and 7.8.

OPERATION NOTE: Make sure you adjust your Total Alkalinity and

pH correctly, this will affect

the sanitizers effectiveness.

The spa is ready for use when the spa water has circulated and the

bromine level remains between 1 and 2 ppm or chlorine level remains

between 3 and 5 ppm.

OPERATION NOTE: For proper water circulation during the ten-minute

Clean cycle the following steps should be performed.

• Place the diverter valve in the middle (split flow) position

• Place air control levers in OFF position by rotating clockwise

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caldera Utopia - serie 2019 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Utopia - serie 2019

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info