Bedienungsanleitung Caldera Utopia - serie 2020 (Seite 29 von 44) (Englisch)

784911

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 26

Spa care and maIntenance

Your CALDERA spa is manufactured from the highest quality, most

durable materials available. Even so, the spa care and maintenance

program you develop will ultimately determine how long your spa, and its

individual components, will last. Regular maintenance and following the

advice in this section will help you to protect your investment.

FILTER MAINTENANCE

At least once a week, check and clean the skimmer basket and weir to

ensure proper filter flow. Remove leaves, foreign matter, and debris. It is

very important to keep your spa filter cartridge clean and free of particles

to ensure proper water flow. A clean filter enables the hydrotherapy

system to function properly and allows for more efficient filter cycles.

Depending on how frequently your spa is used, we recommend cleaning

the spa filter cartridge every four weeks. If this is not done, the filter may

clog and restrict water flow, which causes improper filtration, poor jet

performance and may possibly freeze.

IMPORTANT: The frequency and duration of use, and the number of

occupants all contribute to determining the appropriate time between

filter cleanings. More use means that more frequent filter cleanings will

be required.

FILTER CARTRIDGE REMOVAL AND

CLEANING INSTRUCTIONS

Turn the power to the spa off, then proceed as follows:

Push down slightly and turn filter basket counter-clockwise to unlock, then

pull out the basket and floating weir.

Carefully pull up the filter cartridge and bring it out of the spa.

Always clean the filter using a filter degreaser to remove mineral and oil

build-up. Simply soak the filter in the degreaser (according to the package

directions), then place the filter on a clean surface and spray until clean

using a garden hose. It may be necessary to rotate the filter while spraying

to remove any debris lodged between the filter pleats. Re-insert filter

cartridge.

To return basket and floating weir, insert and rotate clockwise to lock into

position. Then turn spa’s power back on.

NOTE: Replacement filter cartridges are available from your CALDERA

dealer. Refer to the back of this manual to determine the appropriate

size for your spa.

DIVERTER VALVE MAINTENANCE

If your spa’s diverter valves become difficult to turn, it is likely that sand

or grit is lodged inside the valve body. It is very important that this debris

is removed as soon as possible to avoid damage to the valve. To clean

the valves, follow these steps:

1. Turn off power to the spa by tripping the RCD breakers located in

the subpanel.

2. Unscrew the cap ring to remove the diverter valve’s handle as cap

ring comes upward.

3. Remove the valve body by pulling it upward.

4. Wipe the valve body and the interior walls of the valve clean.

5. Lubricate the o-rings with a waterproof lubricant available from your

CALDERA dealer.

6. Reassemble the valve and turn power to the spa on.

VERSASSAGE JET MAINTENANCE

If you notice that the VERSASSAGE jet spins slower than when the

spa was new, or the jets are sticking, the cause may be built-up deposits

inside the jet bearings. To remove the deposits, use the following

instructions:

1. With the spa off, rotate the VERSASSAGE jet face counter-

clockwise until it stops.

2. Once the face stops rotating, use a little extra force to rotate the

face even more counter-clockwise past the locking position until it

stops. Pull face with the body away from the spa.

3. After flushing the bearing inside the body with water, spin the

rotating eye. It should spin very freely. If it does not, place the

bearing end in a cup of vinegar (the vinegar will soften any

deposits). Allow it to soak overnight. The next day, flush with

water and repeat the spin test.

NOTE: If the jets still don't spin freely, a second night of soaking

maybe required. If the bearing still does not spin, you will need to

purchase a replacement assembly from your CALDERA dealer.

COLD WATER REFILL

• When refilling your spa if the tap water is below 10°C (50°F) the spa

may go into a High Limit Protection

mode (causing your spa to stop

functioning). If high limit tripping

does occur, the fastest way to

reactivate the spa control

system is to first disconnect power

to the spa completely, then warm

the two sensors on top of the

heater and the vinyl tubing (located

in the equipment compartment) with a hair dryer for approximately 10

minutes. Once you believe the sensors and heater tubing have been

warmed sufficiently, reconnect power to the spa.

• Blending warm water with the cold tap water so it exceeds 10° C

(50°F) during the refilling process will also achieve the same results if

that is an option for you.

FLOATING WEIR

BASKET

FILTER

CARTRIDGE

STANDPIPE

FILTER SYSTEM

Spa Care and Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caldera Utopia - serie 2020 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Utopia - serie 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info