Bedienungsanleitung Caliber mcd 786 (Seite 4 von 34) (Englisch)

169032

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

E - 3

Installation

INSTALLATION CAUTION

1. Before finally installing the unit, connect the

wiring temporarily and make sure it is all

connected up properly and the unit and

system work properly.

2. Use only the parts included with the unit to

ensure proper installation. The use of un-

authorized parts can cause mal functions.

3. Consult with your nearest dealer if install-

ation requires the drilling of holes or other

modifications of the vehicle.

4. Install the unit where it does not get in the

driver's way and cannot injure the

passenger if there is a sudden stop, like an

emergency stop.

5. If installation angle exceeds 30° from

horizontal, the unit might not give its

optimum performance.

6. Avoid installing the unit where it would be

subject to high temperature, such as from

direct sunlight, or from hot air, from heater,

or where it would be subject to dust dirt or

excessive vibration.

7. Be sure to remove the front panel before

installing the unit.

Fitting the outer sleeve

Fitting the support strap

Remove the transit screws

from the top of the car radio.

Connect the fixing screw to the

rear of the car radio.

Remove the outer sleeve

and place into the

dashboard.

Bend the support strap to

suit the dashboard

aperture and fix to the

underside of the dash

board using the screw

and washer.

Make sure that it is not

angled more than 30°.

Slide the car radio into the

outer sleeve and connect the

spring washer and nut to the

fixingscrew.

DON’T FORGET! Bend the metal tabs on the

outer sleeve outwards and downwards to stop

the sleeve from moving.

30°

Removing the detachable

front panel

Attaching the detachable

front panel

Press the panel release button

on the front panel.

Attach the front panel at the right

hand side first, and then push

the front panel forwards to

lock it securely into place.

DON’T FORGET!

Always turn off the

car radio before

removing the front

panel.

Fixing Screw

Spring Washer

and 5mm Nut

Screw and Washer

Removing the unit

Din Rear-mount

Insert fingers into the

groove in the front of frame

and pull out to remove

the frame.

Insert the levers supplied with

the unit into the grooves at

both sides of the unit as

shown in figure until

they click. Pulling the

levers makes it possible

to remove the unit from

the dashboard.

Fra me

screw

dashboard

bracket

screw

hook

Installation using the screw holes on the sides of

the unit.Fastening the unit to the factory radio

mounting bracket.

NOTE: The mounting box, outer trim ring and

half-sleeve are not used for this method

installation.

Panel Release

button

NOTE: If the D.C.P is dirty,

wipe off the dirt with soft,

dry cloth only. And use a

cotton swab soaked in

isopropyl alcohol to clean

the socket on the back of

the D.C.P.

UP SH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber mcd 786 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber mcd 786

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info