Bedienungsanleitung Caliber RDAB10 (Seite 45 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

781578

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

2. Installation of The Device

Integrating this device with your existing car stereo system is simple and easy. Simply

connect both the existing FM antenna and DAB antenna to the device inputs, then the

FM-modulated DAB radio is readily available via its FM output (F female connector on the

other end of device). This paragraph is intended to guide you step by step how to

correctly configure this device with existing FM antenna, power source, and audio output

delivery to car stereo.

2.1 Connecting to the inputs

 Connect the existing FM/AM antenna (available from the car) to the port (a) of the

unit.

 Connect DAB antenna into the DAB antenna port (b) of the unit.

 Connect IR receiver to the IR port (c). The IR receiver “window” should be located at

positions that can maintain a line-of-the-sight for better command reception.

 Connect the wiring harness correctly to port (d) on the unit. This harness include

+12V car battery supply, ignition wire (ACC), and ground wire. Note that a separate

ISO connection cable may be provided to ease the connection.

2.2 Connecting to the output

In general cases, one simply need to Connect the device’s FM antenna output port (g) to

the car stereo’s FM input as depicted below. No extra wiring is needed. The received DAB

radio contents is already converted into FM signal and fed into the car stereo as a

commonplace FM station.

FM/AM antenna from car

DAB antenna

In.

IR receiver

In.

Battery +12V wire (yellow)

Ignition ACC wire (red)

Ground wire (black)

Wiring harness

(a)

(b)

(c)

(d)

Ear phone socket i.e. port (e) is another audio output option for car stereo to receive the

DAB contents. Note that the Mini USB port (f) is only for software upgrade of the unit. It

is intended for service professionals, not for general public.

Once completed, one can turn on the vehicle and the LED on IR receiver will be ON as a

“power ON” indication to remind users the power is running through the unit.

Note. Please make sure that the unit is fasten tightly and securely. If the unit is loose and dangling, it may

result in malfunction

1. Please make sure that all the wire connections are securely made by inserting jacks until they lock

completely.

2. If your vehicle’s ignition does not have an ACC position, or if the ignition wire is connected to a power

source with constant voltage such as battery wire, the power will not be linked with the ignition (i.e.,

it will not turn on and off along with the ignition). If you want to link the unit’s power with the ignition,

connect the ignition wire to a power source that can be turned on and off with the ignition key.

3. If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old

fuse with one with the same rating.

4. Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do

not remove the caps on the ends of the unconnected wires of the terminals.

Ear phone socket

connects to audio

output)

Upgrade port (mini

USB)

FM output to the car

stereo

(e)

(f)

(g)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber RDAB10 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info