Bedienungsanleitung Caliber RDD401BT (Seite 24 von 28) (Englisch)

497341

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

EN - 23

IMPORTANT:

Remove the two transport screws

on top of the unit before installation.

Otherwise, the player will not work.

Installation

Electronic Connections

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before

connecting, incorrect connection may cause serious damage to this unit. Cut the connector,

connect the colored leads of the power cord to the car battery, as shown in the colour code

table below for speaker and power cable connections.

Location

Function

Connector A Connector B

1 Rear Right (+) - Purple

2 Rear Right (-) - Purple / Black Stripe

3 Front Right (+) - Gray

4 Battery 12V(+)/yellow Front Right (-) - Gray / Black Stripe

5 ANT/Amp control/blue Front Left(+) - White

6 Front Left(-) - White / Black Stripe

7 ACC+/red Rear Left (+) - Green

8 Ground/black Rear Left (-) - Green / Black Stripe

Preparation

1. Disconnect battery

Before you begin, always disconnect the

battery negative terminal.

Note:

If the unit is to be installed in a car

equi pped w ith a n on-board drive or

navigation computer, do not disconnect the

battery cable. If the cable is disconnected,

the computer memory may be lost. Under

these conditions, use extra caution during

installation to avoid causing a short circuit.

2. Remove transport screws

CAUTION:

For proper operation of the player, the

chassis must be mounted within 20° of

horizontal. Make sure the unit is mounted

within this limitation.

3. Remove unit from sleeve

Lift latches on both sides of sleeve to

remove half-sleeve from the unit.

Mounting sleeve installation

1. Slide the mounting sleeve off the chassis.

If it is locked into position, use the removal

tools (supplied) to disengage it.

2. Check the dashboard opening size by

sliding the mounting sleeve into it.

If the opening is too small, carefully cut or

file as necessary until the sleeve easily

slides into the opening. Do not force the

sleeve into the opening or cause it to bend

or bow. Check for sufficient space behind

the dashboard for the unit chassis.

This unit can be installed in any dashboard

with a suitable 183mm(w) x 52mm (h)

opening as shown above. The dashboard

should be 4.75 mm - 5.56 mm thick in order

to be able to support the unit.

3. Locate the series of bend tabs along the

top, bottom, and sides of the mounting

sleeve. With the sleeve fully inserted into

the dashboard opening, bend as many of

the tabs outward as necessary to firmly

secure the sleeve to the dashboard.

4. Place the unit in front of the dashboard

opening so the wiring can be brought

through the mounting sleeve. Follow the

wiring diagram carefully and make certain

all connections are secure and insulated

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber RDD401BT Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber RDD401BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info