Bedienungsanleitung Caliber RDD788 (Seite 12 von 28) (Englisch)

781576

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

LOC

VOL 32

Radio operations

To select the radio mode

Press the button to access the

source interface, then press the or

button on the front panel or pressing the

or button on the remote control to select

select the radio mode. You will see the

following radio screen on the

one of the three

MODE

Stereo/Mono

◄

►

TFT screen.

In radio mode, press the button

repeatedly to select radio

broadcasting bands: FM 1-> FM 2 -> FM 3.

Press the or button, the automatic

search will start. It will search upward or

downward for the strong signal radio station

within the current band.

Press and hold the or button until

“MANU” appears on the TFT screen, it will

change into manual searching mode.

Press the or button repeatedly to

manually search upward or downward step

by step for the desired radio station within

the current band. For fast manual

searching, press and hold the or

button.

In manual search process, if the both

buttons haven’t been pressed within 5

seconds, it will change into automatic

search mode automatically. “MANU”

disappears on the TFT screen.

FM station is received in stereo mode.

However, if the signal weak or reception is

not as good as you would like, switching to

MONO mode usually improves the overall

sound quality

To select a radio band

Auto/ Manual tuning

BAND

- Automatic search mode:

- Manual search mode:

Press the button on the front panel or

briefly press on the remote control

to choose FM STEREO or MONO audio

effect.

In urban settings, most stations are strong

enough and it should be set in LOCAL

mode.

Switch to DX (distant) mode to search for

stations with weaker signals.

Press and hold the button on the

head unit or briefly press the button

on the remote control to choose local

reception or DX(distant) reception mode.

You can store up to a total of 18 FM radio

stations in the memory (manually or

automatically.

- Select a band (if needed)

- Select a station by or button, refer

to auto / manual tuning.

-HoldaPre-setbutton(1-6)foratleast2

seconds.

- Select a band (if needed).

- Press a preset button (1-6) briefly to

recall the stored station.

Press the button to scan each preset

station. It will play a station for a few

seconds, then go to next station until all 6

stations are scanned, finally the radio will

play at the preset station where scanning

started. The preset station number on the

LCD will flash during the process. When

you hear a station that you wish to listen to,

press the again to stop the preset

scanning.

Press and hold the button for more

than 2 seconds to start auto store. The radio

will scan from the lowest frequency, and

automatically store the 6 strongest stations

into the preset memories. When auto store

is complete, the radio will start preset scan

to the stored 6 station

MO/ST

PTY/LOC

LO/DX

- To store a station:

- To recall a station:

- Preset scan:

AS/PS

- Auto store:

AS/PS

Local/Distant

To store / recall a preset radio stations

Auto store / Preset scan

Stereo/mono

Local/distant

Radio band

Frequency

Clock

Volume

Preset

station

number

TA AF

Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber RDD788 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber RDD788

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info