Bedienungsanleitung Calor 5033 alte rn prog (Seite 17 von 20) (Englisch, Holländisch, Französisch, Spanisch)

306739

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English

1 - DESCRIPTION (see exploded view) :

Your machine is composed of:

2 - SAFETY INFORMATION

Voltage:

•

Models 50.23, 50.27 and 50.33: 220-240 V

•

Model 50.40: 230 V

•

Model 50.24 is dual voltage (115-127 V or 220-240 V).

•

Always make sure the voltage displayed at the back of the washing machine is appropriate for your power supply. If not, push the

toggle switch all the way to one side until the correct voltage is displayed.

•

ALWAYS CONNECT MODEL 50.40 TO A GROUNDED (THREE-HOLE) SOCKET.

A plastic tub (A) which has:

•

1two water level marks: the low water mark (1) indicates the

lowest acceptable water level for any size load (always ﬁll to this

mark even if the load is small) and the high water mark (2)

indicates the highest level (water plus laundry) to which the

machine may be ﬁlled. It is important to use the right proportion of

water for the amount of laundry otherwise the laundry may not be

agitated vigorously enough,

•

1a drain oriﬁce (3) at the bottom right of the machine to drain

water from the tub,

•

1an emptying system controlled by a drain handle (4) on the top

right of the machine.

In addition, on Model 50.40:

•

1A heater (5) on the left of the

machine with a three-prong plug, an overheat switch and a ﬂoater to

p r event heater operation when the water level in the tub is too low

•

1An opening at the top centre of the machine to discharge water

during rinsing.

An easy-to-remove washing unit (B) which has:

•

1a rotor plate (8) and roller track (7),

•

1a roller ring with six rollers (9),

•

1a rotor (10), the large rotating plate under the tub; the

shape of the raised cross on the rotor has been designed

speciﬁcally for gentle washing by combining a slow tumble

and alternating spin motion,

•

1a partition (11) to isolate the drive shaft (12) and pinion

(13).

A motor unit (C), which has:

•

1a motor with overheat protection that stops the motor in case of

accident, overheating or incorrect positioning; the motor will start

once parts have cooled (which may take up to 15 minutes),

•

1a power cord storage cassette.

In addition, on Models 50.23, 50.24, 50.33 and 50.40:

•

1a timer (16) and timer display (15) to automatically stop the

machine after the desired wash time.

On model 50.40:

•

1an ON/OFF switch (17) for the heater.

On Model 50.27:

•

1an automatic programmer (16) and programmer display (15) to

select any of three wash cycles,

•

1pre-wash ;

•

1soak or ;

•

1wash and single, double or triple rinse;

the machine stops automatically once the selected cycle is

complete.

A lid (D) with viewing window (window not on all models).

A ﬁll hose (E) and hose end-piece (F).

Important:

•

Never operate the washing machine unless it contains sufﬁcient water.

•

Unplug the washing machine before removing the motor unit.

•

Never ﬁll the tub with ﬂammable liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Calor 5033 alte rn prog Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info