Bedienungsanleitung Cambridge 751RV2 (Seite 39 von 40) (Englisch)

581025

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

751R V2azur

ENGLISH

A low hum or buzz sound can be heard

Power cords or lighting placed near this product.

Analogue inputs not connected securely.

Sound is not audible from one channel

Speaker connections disconnected.

Speaker set to "None" in OSD setup menu.

Sound cuts off when listening to music or there is no

sound even though power is ON

Speaker impedance is less than prescribed for the 751R V2.

The unit is not adequately ventilated and may be overheating.

Low bass or "phasey" response

Speaker polarity (+/-) of one or more speakers is reversed.

An unusual hissing noise is heard when listening to a

radio broadcast in stereo, but not heard when listening

in mono

A slight noise may be heard because the method used for modulation of FM

stereo broadcasts is different than that used for mono broadcasts.

Aerial quality also effects the level of hiss heard.

Noise is excessive in both stereo and monaural radio

broadcasts

Poor location and/or direction of the antenna.

Transmitting station is too far away.

No sound from the rear speakers

Source being played is not recorded in surround sound.

Speaker/s set to "None" in OSD setup menu.

A stereo mode has been selected.

No sound from the centre speaker

Centre speaker has been set to "None" in OSD setup menu.

A stereo mode has been selected.

No sound from the subwoofer

Sub has been set to 'Off' in the OSD setup menu or via the remote.

DTS Neo:6, DD Dolby Pro Logic II/IIx modes (which have no LFE channel)

have been selected with all speakers set to "Large" (and bass augment off).

Remote control is not working

The batteries are at.

The remote is too far from the receiver or out of the effective range.

No sound from speakers when connected to a digital

input or HDMI

Audio input type is set to analogue (check display). Press the Audio Input

Type button to switch to digital or HDMI.

No sound from speakers when connected to an analogue

input

Audio input type is set to digital. Press the Audio Input Type button to switch

to analogue (check display).

Audio input type can also be set in the Input/Output Setup menu of the OSD.

No sound from any speakers

Receiver is set for 'Pre-out' operation.

By entering the OSD menu, selecting the input/output setup menu, the

Preamp out setting can be changed from 'Normal' to 'Pre-out'. This disables

the internal ampliers when an external decoder amplier is being used.

Reset this to 'Normal' to restore sound.

Troubleshooting

No sound from front speakers, but rear speakers work

Receiver is set for 'Ext 2Ch' operation.

By entering the OSD menu, selecting the input/output setup menu, the

Preamp out setting can be changed from 'normal' to 'Ext. 2 Ch'. This disables

the internal ampliers for the front channels when an external amplier is

being used to drive those channels. Reset this to 'Normal' to restore sound.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge 751RV2 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge 751RV2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info