Bedienungsanleitung Cambridge Audio AXA25 (Seite 5 von 8) (Englisch)

699768

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

AXA25

Rear panel connections

Front panel controls

USB 5V 500mA

Designed & Engineered in Great Britain

Assembled in China

Power AC

Left

Loudspeaker

Right

Loudspeaker

Left

Loudspeaker

Right

Loudspeaker

Power Rating: 220–230V AC ~ 50/60Hz

Max Power Consumption: 180W

AXA25

Integrated Amplifier

A4 A3 A2 A1

A4A3A2A1

Rec Out

Loudspeaker Terminals

Impedance 8 ohms

1 2 4

3 5

AUDIO INPUTS (A1-A4)

These inputs are suitable for any ‘line level’ source equipment such as the audio

outputs of CD players, streaming devices such as a Chromecast Audio (RCA

Phono to jack cable required) etc.

REC OUT

Connect to the recording input of a CD recorder input, tape deck or other

compatible recording device etc.

This output provides a constant high level output that does not uctuate with the

volume, balance or tone controls of the main unit. For this reason, the AXA25

cannot be used as a Preamplier only or with a subwoofer.

USB POWER 5V 500MA

This USB connection is designed to power a device such as a Streaming device

or Bluetooth adaptor.

Note: This is not an input so will not allow you to play audio directly to the unit.

POWER BUTTON

Switches the unit between Standby mode (indicated by dim LED) and On (indicated

by bright LED). Standby mode is a low power mode where the power consumption is

less than 0.5 Watts.

This product has APD (Auto Power Down) enabled as default. After inactivity of 20

minutes, the product will automatically switch to Standby.

Auto Power Down (APD)

You can enable and disable the units APD setting. This can be adjusted by pressing

and holding the Power button until the LED ashes in sequence.

The two options below show which option is selected.

Standby ashes 5 times - APD disabled

Standby ashes 10 times - APD enabled

Note: Make sure the unit is On, before making changes to the APD function.

BASS AND TREBLE

These controls allow subtle adjustments to the tonal balance of the sound. In

the central position these controls have no eect. They only modify the sound

through your loudspeakers, and do not aect the signals sent through the Rec Out

connections. If the musical recording is of poor quality or other factors are aecting

the sound quality, it may be necessary to adjust the tone controls to compensate.

VOLUME CONTROL

Use to increase or decrease the audio output level of the unit.

Note: The volume control does not aect the level of the ‘Rec Out’ output as this has

a xed level

LOUDSPEAKER TERMINALS

Connect the wires from your left channel loudspeaker to the Left positive and

negative terminals and the wires from the right channel loudspeaker to the Right

positive and negative terminals.

In each case, the red terminal is the positive output and the black terminal is the

negative output.

Care should be taken to ensure no stray strands of wire are accidentally

connecting speaker outputs together as this may cause damage to the unit.

Please ensure that the loudspeaker terminals have been tightened adequately

to provide a good electrical connection. It is possible for the sound quality to be

aected if the screw terminals are loose.

AC POWER SOCKET

Once all connections are complete, plug the AC power cable into an appropriate

mains socket and turn the unit on.

Please only use the power lead supplied with the unit.

TREBLEBASS

A4 / AUX

BALANCE

VOLUME

AUX IN

A25AX

BALANCE

This control allows you to adjust the relative output levels of the left and right

channels. In the central position the output from each channel is equal. This control

only modies the sound through your loudspeakers – it does not aect the signals

sent through the Rec Out connections.

SOURCE SELECTOR SWITCH

(A1,A2, A3 AND A4/AUX)

Select the appropriate input source component that you wish to listen to. The signal

selected is also fed to the Rec Out sockets so that it may be recorded. The input

should not be changed whilst recording.

AUX IN

This source input allows you to connect a portable audio device such as an MP3

player or streaming device directly into the front of the unit using a 3.5mm stereo

Aux lead.

Once plugged in, this input is automatically selected, although other inputs apart

from A4 can still be selected once a stereo-jack is plugged in. The A4/AUX option on

the front of the unit will select this input whilst a stereo-jack is plugged in.

Note:

– Plugging a source into the front panel Aux input overrides the A4 input. Simply

remove the jack from the front panel to automatically re-enable the A4 input.

1 2 3 4 5 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio AXA25 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio AXA25

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info