Bedienungsanleitung Cambridge Audio Azur 551R V2 (Seite 15 von 28) (Englisch)

656752

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

551R V2azur

ENGLISH

Once nished the unit will display a screen similar to the one below reporting

which speakers were found and any that appear out of phase.

azur 551R

Continue : [ENTER]

The speakers that have been

found are:

L C R SL SR LB RB SW

All speakers are in phase

If any speakers appear unconnected or out of phase carefully check the

connections on the speaker and the back of the unit. Also check any bi-wiring

links that might be present on the speaker. For any out of phase speakers

check that the relevant + terminal of the 551R V2 goes to the + terminal

of that speaker and similarly the – terminal of the 551R V2 goes to the –

terminal of the speaker for that channel.

If necessary press the OSD button to perform a retest or press Enter to start

the second part of the auto setup procedure as below.

azur 551R

The unit is now measuring the

Distance and Level settings for

your speakers

Please wait....

Again a series of test signals will now be output from all of the connected

speaker terminals and Subwoofer. The 551R V2 uses these to measure the

levels and distances (and hence introduce the correct delays) appropriate to

your speakers and room characteristics.

When the auto setup of the 551R V2 is completed successfully, the 551R V2

will return to the Auto Setup Menu.

azur 551R

Video In. Select

Audio In. Select

Tone/Sub Config.

Speaker Config.

Speaker Distance

Speaker Level

Speaker Xover

Auto Setup

Advanced Setup

OSD Setup

Please press ENTER to start

auto setup.

WARNING: High Volume Test Tones

Quit: [I/O] Enter: [ENTER]

The Speaker Distance and Level Calibration settings for each speaker will

have been updated.

It is of course now possible to go into the Speaker Delay and Level

Calibration menus if you want to manually check/adjust the settings made by

the CAMCAS system, and it is always advisable to check them as no system

can be totally foolproof.

To exit the auto setup menu of the 551R V2 continue to press the OSD

button on the remote control to exit all menus or until 'OSD 'is no longer

displayed on the front panel. You can now unplug the microphone and put

it away for future use.

Note:

– If the auto setup of the 551R V2 is unsuccessful for some reason a 'Fail'

message will appear on the OSD. Included in this message will be details

of the speaker channel or channels which have not been successfully

adjusted. If this is the case, please again check that the speaker or

speakers detailed in the OSD as 'failed' are connected correctly & have

not been wired out of phase. Also check the microphone connection and

any other external issues that could have affected the tests such as noise

in the room etc.

– Like all such systems CAMCAS has some limitations. Speakers that exhibit

very strong phase angles or deliberately wire some drive units out of phase

can of course appear to the system as an out of phase speaker when

correctly connected. If a speaker is reported as out of phase but is correctly

wired please consult the speakers manufacturer in case this is the case.

Similarly bi-polar speakers which radiate in more than one direction can

make it difcult to measure the distance and sometimes level accurately as

you might expect.

In all cases it is always advisable to manually check the settings CAMCAS has

made for a 'reality check' to ensure there are no obvious errors.

3. Assigning Video inputs

The 551R V2 has 6 HDMI (High Denition Multi-Media Interface) inputs,

and 2 HDMI outputs. HDMI is a fully digital audio/video system for picture

and audio in digital format for best possible picture quality. DVI (Digital

Video Interface) is a subset of HDMI that uses different connectors and only

supports digital video (no audio). The 551R V2 is compatible with DVI in that

simple passive DVI-HDMI adaptors are available which allow the conversion

of the DVI connector to an HDMI format connector (and back again if

required) for routing via the 551R V2.

HDMI outputs on Blu-ray, DVD players and Set-top boxes also often support

higher resolution formats including progressive scan types. Consult both your

HDMI source and TV manuals for details, it is often possible to select from

various options, you will want to select the highest quality output that both

your source and TV are compatible with.

From Blu-ray players, HDMI can also carry the latest Dolby Digital Plus and

True-HD formats as well as DTS-HD High Resolution and Master Audio.

Ensure that the HDMI output of your player has been set to 'Bitstream' or

'Raw' to pass the formats to the 551R V2 for decoding.

Also some Blu-ray players feature settings to allow down conversion of Dolby

Digital Plus etc. to backwards compatible Dolby Digital 5.1 for older AV

receivers which do not support these formats.

Ensure any such settings are disabled to allow our 551R V2 access to all

the latest formats.

For all the above reasons HDMI is the preferred connection method for both

Audio and Video.

Select the Video In. Select menu.

For each source the currently selected video input type will be shown. It is

possible to assign any of the video input sockets to each source in turn,

except Tape/MD/CDR source which is audio only.

The Options are HDMI 1, HDMI 2, HDMI 3, HDMI 4, HDMI 5 and HDMI 6.

azur 551R

Video In. Select

Audio In. Select

Tone/Sub Config.

Speaker Config.

Speaker Distance

Speaker Level

Speaker Xover

Auto Setup

Advanced Setup

OSD Setup

BD/DVD

CD/Video 1

Video 2

Video 3

Aux/TV

7.1 Direct

Back: [I/O]

HDMI 1 < >

HDMi 2 < >

HDMi 3 < >

HDMi 4 < >

HDMi 5 < >

HDMi 6 < >

Cambridge Audio Azur 551R V2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 551R V2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info