Bedienungsanleitung Cambridge Audio Minx Air (Seite 9 von 13) (Englisch)

763879

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

iPad

3. Open a new page in your internet browser (Internet Explorer, Safari, Chrome etc).

In the address bar of your browser, type 192.168.1.1 followed by 'enter' and the

Minx Air setup page will be displayed.

4. Select your home wi- network from the 'Service Set ID (SSID)' drop down list

of choices.

The lists shows all the networks the Minx Air can nd locally.

5. Now type your home Wi-Fi/Network password into the red box, and click the

'Apply' button.

Note: If you don't know your Wi-Fi password key, it's commonly found on a label on

your internet modem/router.

6. If you are happy that you have entered your details correctly, click 'OK' to nish.

The Minx Air set-up page may now display an 'error' or 'no data' received' type

message. Don't worry, this is normal. You can now close your internet browser.

7. After a few seconds, the Minx Air will be connected to your network (successful

connection is indicated by a solid green light on the rear of the product). This

can take up to 30 seconds.

Note:

– If the light on the rear continues ashing green , this indicates that the Minx

Air has been unsuccessful with the wi- connection. Carry out a factory reset and

repeat the process.

– If your computer/tablet has not already done so automatically, change the Wi-Fi/

network setting on your computer/tablet back to your home network.

Connecting to a wireless network using WPS

If your router supports WPS (Wi-Fi Protected Setup) then this is a simple method to

connect the Minx Air to your network without needing to know your wi- network key

or broadcast network name SSID.

WPS allows two devices to discover each other for a short time (usually a minute or

two) after the WPS buttons have been pressed on both devices.

To connect using WPS simply press the WPS button on your router (please consult

router instructions for details) then shortly after press the WPS button on the rear

panel of the Minx Air (briey press it once).

The WPS light on the rear of the Minx Air will ash orange > green > red

for up to 2 minutes whilst the Minx Air looks for your router.

If the connection is successful connection the WPS light will turn solid green and

your wi- connection is ready.

Connecting to a wired network

Note: Make sure that the Minx Air is switched off before plugging in the ethernet

cable.

Plug one end of a network cable (Category 5/5E straight through Ethernet cable)

into the LAN port on the back of the unit and the other end directly to a free port

on your router.

Note: Only connect the LAN port of the player to an Ethernet port that supports

10BASE-T or 100BASE-TX. Connecting to any other ports or jacks, such as a phone

jack, can damage the unit. Now turn on your Minx Air.

The Minx Air should automatically connect to your network via DHCP; this means it

will be given an IP address by your router automatically.

NOTE: Your Minx Air must rst be connected to a network via Wi-Fi or

Ethernet for Internet Radio or Airplay streaming to be available.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Minx Air Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Minx Air

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info