Bedienungsanleitung Cambridge Audio Topaz SR10 (Seite 6 von 12) (Englisch)

497546

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Speaker A/B button

The Speaker A/B button toggles between the two sets of loudspeaker

terminals. The options are speaker A only, speaker B only, speaker A and

B together, and both sets of speakers off.

: ‘Speaker off’ is different to the mute function, as the Rec Out and

Headphones outputs are still enabled.

Menu button

Pressing this once will select the Bass option. Pressing a second time will

select the Treble option and pressing a third time will select the Balance

option. When one of these options is selected, the volume control will

adjust the level. If nothing is pressed for a while, the source will be

displayed and the volume control will go back to controlling the volume

level.

Infrared sensor

Receives IR commands from the supplied remote control. An

unobstructed line of sight between the remote control and the sensor is

required.

Volume control

Use to increase or decrease the level of the sound from the outputs of the

unit. This controls the volume level of the loudspeakers, Sub-out and

headphones. It does not affect the level of the ‘Rec Out’ output. The

volume control will also change the level of bass, treble and balance in the

menu options.

MP3 input socket

This source input allows you to connect a portable audio device such as

an MP3 player directly into the front of the unit using a 3.5mm stereo-jack.

Once plugged in, this input is automatically selected, although other

inputs can still be selected once a stereo-jack is plugged in. The MP3/AUX

button on the front of the unit will select this input whilst a stereo-jack is

plugged in.

– Plugging a source into the front panel MP3 input overrides the Aux input.

Simply remove the jack from the front panel to automatically re-enable

the Aux input.

– Also note that as the output level of MP3 players tends to be quite low,

the SR10 adds 10dB to the current volume setting when (and only

when) the MP3 input is selected.

SR10

Stereo Receiver

Phones Mode / Store

Volume

On / Off

Speaker A / B

1 / 6 2 / 7 3 / 8 4 / 9 5 / 10

MP3 In

PhonoMP3 / AuxBD / DVDCDFM / AM

Front panel controls

1 2 3 4

Power On/Off

Switches the unit on or off.

Headphones socket

Allows for the connection of stereo headphones with a ¼ inch jack plug.

Headphones with an impedance of between 32 and 600 ohms are

recommended.

Plugging in headphones will automatically mute the loudspeaker

outputs.

Skip/Scan buttons

The skip scan buttons are used when the FM/AM tuner is selected. These

buttons have different uses depending on the mode selected:

In Preset mode - Steps up or down through the user-stored presets.

In Auto mode - Searches for the previous or next available station. The

unit stops at the next strong signal it finds.

In Manual mode - Allows manual stepping up or down of the frequency.

When Preset mode is activated, the unit will automatically tune to

the first available preset.

Mode/Store button

Used for AM/FM mode. Press to cycle the tuning mode between Preset,

Auto, and Manual modes. Pressing and holding the button will allow the

current selected station frequency to be stored in the preset bank. First

press and hold the button then use the   or Preset buttons to select

the preset location for the station to be stored to. Press the Mode/Store

button again to confirm and store the preset.

: In ‘Store’ mode, if no button is pressed for a while, the unit will come

out of ‘Store’ mode and the preset will not be saved.

Input source buttons (CD, BD/DVD, MP3/Aux,

FM/AM, Phono)

Press the relevant source button to select the desired input source.

: The FM/AM source is built into the SR10. This button toggles

between the FM mode and AM mode when pressed more than once.

Preset buttons (1/6, 2/7, 3/8, 4/9, 5/10)

Used for AM/FM modes. The preset buttons are used to select user-stored

station presets. Pressing a preset button once will select one of the first 5

preset, then pressing the same preset button again will toggle to the next

preset (1 and then 6 for instance). These presets are stored separately for

each waveband i.e. there are 10 for FM and 10 for AM press the FM/AM

button to switch between bands and sets of 10 presets.

As well as these 10 per band available directly from the front panel

buttons a further 5 presets (11-15) per band can also be accessed by

using the up/down buttons to cycle through all 15 presets.

Display

Used to display information such as the selected input source, volume and

tone/balance levels. When the FM or AM tuner input is selected, the radio

frequency or RDS station name will be displayed.

When first purchased, the display will have a protective film over the

top. Peel this off for a clear display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Topaz SR10 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Topaz SR10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info