Bedienungsanleitung Cambridge Audio Minx Air200 BT (Seite 8 von 13) (Englisch)

581842

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Standby/On button

Controls the standby state of the unit. When the top panel Standby/On button on

the unit itself is illuminated red, the system is in its <0.5W standby state. When

the button is illuminated white the unit is on and ready for playback. When the unit

is rst turned on it takes approximately 20 seconds to fully power up and become

active. During this phase the top panel button will blink red on and off .

Volume buttons

Volume up is labelled ‘+’, volume down is labelled ‘-’.

Mute button

Press to mute and press again to un-mute the unit.

X Button

Stops streaming playback (and returns the unit to the analogue inputs).

Starting up streaming playback from Bluetooth, Airplay or Internet Radio will always

cause the Minx Air to automatically switch back to that source. Otherwise the

system defaults to the analogue inputs.

To stop Bluetooth, Airplay or Internet Radio playback and return to the analogue

inputs just press the X button. Press a second time to mute the analogue input.

Pairing button

Used to pair (connect to) Bluetooth devices so that they can be played back

wirelessly. When the pair button is pressed the pair button on the top panel of the

unit will blink blue for approximately 30 seconds. This indicates that the system is

in pairing mode. See later section.

Presets buttons 1 – 10

Press to recall an Internet Radio preset. As shipped from the factory 10 stations will

have been pre-assigned, 5 can be accessed from the top panel buttons, all 10 can

be accessed via the remote. To change the assigned stations use the free Minx Air

App for Android or Apple devices, see later section.

Bass controls

Allows setting of the bass/low frequency response of the unit tailored to your taste

and the acoustics of your room.

Bass up is labelled ‘+’ and bass down is labelled ‘–’.

Getting startedRemote control

For help connecting Minx Air to your Wi-Fi network, we recommend watching the

help videos available at http://www.cambridgaudio.com/MinxAirSupport. Also

please see the Wi-Fi setup guide supplied with your unit.

Note: If you make a mistake during the connection process, reset the Minx Air. To

do this, press and hold the Standby/On button and WPS button on the rear panel

for 10-15 seconds until the Minx Air switches off, then repeat the connection

process.

Network connections

Before you can use your Minx Air for iRadio/Streaming you must have the following:

• A broadband internet connection (such as ADSL) to a suitable internet service

provider (ISP).

• A network connection either wirelessly via 802.11b/g or n Wi-Fi or wired Ethernet

connection (10 or 100 M bits/sec via an RJ45 connection).

In many cases the broadband modem, router and wireless access point will be a

single combined unit supplied by your Internet Service Provider or bought from a

computer store.

If your wireless network is congured to use Wired Equivalent Privacy (WEP) or Wi-Fi

Protected Access (WPA) data encryption then you will need to know your WEP or WPA

key so you can get the Minx Air to communicate with the network.

IMPORTANT:

Before you continue, make sure that your wireless access point or router is

powered up and working with your broadband internet service (use your computer

to verify this). To get this part of the system working you must read the instructions

supplied with the wireless access point or router.

The Minx Air can be congured to connect to a Wired or Wireless network.

For wired setup, see later section 'Connecting to a wired network'.

Connecting to a wireless network

1. Connect the Minx Air to the mains power and press the button on top of the

unit. Wait for up to 20 seconds for the ashing light on the rear panel to ash

green

and orange . If the light does not ash green and orange after 20

seconds, please carry out a factory reset as detailed above, and start again.

2. Go to your computer/tablet and click on the wi-/network logo and select Minx

Air_XXX.

Mac

3 4 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Minx Air200 BT Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Minx Air200 BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info