Bedienungsanleitung Cambridge SoundWorks Desktop Theater 5.1 DTT2500 Digital (Seite 10 von 26) (Englisch)

750733

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Speaker Wire and Stand Installation

Typically, the 3 meter speaker

cables will connect the front and

center satellites to the Decoder

Amplifier and the 5 meter cables

will connect the rear satellites to

the Decoder Amplifier. A panel of

twelve self-adhesive labels is

provided to identify each satellite

and subwoofer and the opposite

end of the cable connected to a

satellite and subwoofer.

1. Identify a 3 meter cable. Most

often, a satellite will be used

with a desktop stand. In this

case, thread the bare wire end of

a 3 meter cable through the hole

in the desktop stand. Connect

this end to a satellite (as shown

in Diagram K). Carefully insert

the desktop stand’s attachment

arm into the socket in the back

of the satellite, taking up any

slack in the cable as required.

2. To use this satellite in the front

left position, remove the backing

from the small, round “L” label

and apply it to the back of the

satellite (see Diagram K).

3. Remove the backing from the

remaining, longer “L” label and

wrap it around the opposite end

of the speaker cable near the

RCA-type plug.

4. Place the satellite in the front

left position.

5. Repeat this process using

another 3 meter cable for the

front right satellite, using the

“R” labels.

6. Connect another 3 meter cable to

a satellite. Use the “C” (center)

labels. If used, the Monitor

Stand attaches to the satellite in

the same manner as the

Desktop Stands, although it

does not have a hole for the

speaker wire. Route the wire to

the left or right side of the

attachment strut. Position the

satellite.

7. If you wish to use the Floor

Stands with the rear satellites,

assemble the stand according to

Attaching The Floor Stand

instructions on page 7. Use the

RS and LS labels (right and left

surround) and 5 meter cables.

8. Connect the subwoofer using the

last 3 meter cable to the “SUB”

labels.

Diagram K: To connect the

speaker wire to each satellite,

press one of the spring-loaded tabs

to expose the connection hole.

Insert the bare end of the wire

into the exposed hole, then release

the tab to lock the wire in place.

Connect wires with red bands to

red tab connectors, and unmarked

wires to black tab connectors.

Notes: Matching red wires to red

tabs and unmarked wires to black

tabs insures the speakers all play

“in phase”. “Out-of-phase”

connections will do no electrical

harm, but the overall sound

quality will be greatly reduced.

You can substitute regular 18

gauge speaker wire to create

longer cables, if needed.

DOLBY DIGITAL

(AC-3) SPDIF IN

SPEAKER OUTPUTS

LINE IN REAR IN

C SUBWOOFER RS LS R L

15V

DC IN

DIGITAL

DIN ANALOG AUTO

INPUT

SUBWOOFER

LINE OUT

SUB

SUB RS LS

SUB

REAR

RIGHT

0420000547 REV. B SINGLE 2/9/01, 1:50 PM10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge SoundWorks Desktop Theater 5.1 DTT2500 Digital Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info