Bedienungsanleitung Camina-Schmid Ekko-W (Seite 32 von 44) (Englisch)

810637

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Repair hints

8. Repair hints

8.1 Cracks in the combustion chamber

lining

Cracks in the ﬁre box lining fundamentally do not adversely

aect the function of the ﬁreplace insert. They only need to

be replaced if pieces of the ﬁrebox lining have broken o and

the stove body can no longer be protected.

8.2 Damage to paintwork

Only repair paint damage with heat-resistant original paint.

Use spray paint to repair larger areas of damage. Ask your

dealer for Camina & Schmid stove paint.

9. Inspection and maintenance

9.1 Safety inspection

You will obtain optimum, environmentally-friendly heating

results with regular inspection of the ﬁreplace and the

chimney by a technician. The technically correct function

of all safety parts will guarantee your safety. We therefore

recommend an annual inspection by a specialist ﬁrm or a

chimney sweep.

9.2 Maintenance

The ﬁreplace needs to be maintained regularly by a specialist

company and/or by a chimney sweep. The ACTUAL condition

of the ﬁreplace needs to be compared with the INTENDED

state. Essentially this is a visual inspection. The results need

to be recorded in writing. Replace or repair faulty parts

immediately.

9.3 Maintenance information

NOTICE

Please refer to the additional maintenance instructions in

the separate instructions for the ﬁreplace components,

such as heat storage vessel, diaphragm expansion vessel,

water pump!

Only top up with treated water!

9.3.1 In the event of malfunctions, faults

Shut down the ﬁreplace in the event of problems or faults –

such as decreasing heat output, decreasing draught, escape

of smoke and/or water. Arrange for the cause to be rectiﬁed

immediately by a technician.

9.3.2 After operating breaks

After all breaks in operation and longer pauses, check the

heating and exhaust paths, speciﬁcally the chimney for

blockages and remove blockages before starting up the

ﬁreplace again. Check the entire ﬁreplace for faults!

9.3.3 At the start of the heating period

Check and ﬁll all hydronic lines of the ﬁreplace using

separate instructions or with the help of a technician and set

the temperature and pressure setpoints. Check that all the

safety devices and displays (e.g. thermal discharge safety

device, safety valve, thermometer) are all working properly.

Make sure that all the ﬂue gas paths are clear. Arrange for a

technician to rectify any faults or defects.

9.3.4 Annual maintenance of the hot water

boiler

Arrange for a technician to check the hot water boiler, ﬂue

gas paths and ﬂue gas pipes annually or in the event of

heavier loading (frequent heating, incomplete combustion of

the heating gases) more often and also after the chimney has

been cleaned.

Repair or clean any deposits, functional faults and defects.

9.3.5 Maintenance of the safety devices in

the water circuit

Check the thermal discharge safety device at least once a

year for correct working order. To do so, press the red button

on the valve. This may be a little sluggish. Use a large ﬂat aid

to help you with this.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Camina-Schmid Ekko-W Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Camina-Schmid Ekko-W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info