Bedienungsanleitung Campingaz 3 Series RBS LX Plus (Seite 10 von 132) (Alle Sprachen)

662208

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

- that the ventilation openings in the gas receptacle housing

are not obstructed, if appropriate.

- that the grease trap(s) is (are) correctly inserted into its

(their) compartment and that it (they) is (are) correctly

positioned, as far as it (they) will go.

- that the heat reflector is correctly installed in the bottom of

the bowl.



cleaning).

h) LIGHTING THE BARBECUE BURNERS

- Open the lid.

- Make sure that the control knobs are in the "OFF"

position (O).

- Open the gas cylinder valve.

- Press and turn the control lever in a counter-clockwise

direction and put in the full flow position (

), then

press the ignition button immediately (

). Keep the

button pressed until the burner lights.

- If the burner does not light after 10 seconds, wait 5

minutes and try again.

- Adjust the flame to the desired height by turning the

knob to ( ) or ( ).

Once the burner is lit, there are two options for lighting

another burner:

- The first option is to repeat the ignition procedure

described above.

- The second option is simply to open the 2nd valve,

        

(

- You can also light both burners simultaneously. Open

        ) and

press the ignition button (

) until the burners light (10

seconds).

- If the electronic ignition system does not work, light the

barbecue manually (next paragraph).

Lighting the burner manually

- If the electronic ignition system fails to work, use a

match to light the burner.

- Open the lid.

- Make sure that the control knobs are in the "OFF"

position (O).

- Remove one of the cooking grids to gain access to the

burners.

- Turn on the gas supply (valve or lever on the regulator).

- Put a lighted match in front of the burner.

 

position (

- Adjust the flame to the dimensions of the recipient by

using the two flow positions: HIGH ( ) or LOW ( ).

Once the burner is lit, replace the grid or hotplate.

Once the burner is lit, there are two ways of lighting another

burner:

 

 

burner lit, then the other burners in turn by turning the

adjustment button to the full flow position ( ).

- You can also light both burners simultaneously. Open

both valves to their full flow position (

) and put a

match to both burners.

i) EXTINGUISHING THE BARBECUE

Set the control knobs to the "off" position (O), then close the

cylinder valve.

j) LIGHTING THE SIDE BURNER

(depending on the model)

The side burner can be used alone or at the same time

as the grill.

Lighting:

- Open the gas cylinder valve.

- Check gas circuit sealing from the frame to the hot plate

(see § f).

- Open the hotplate lid and retract it to the back of the

hotplate, sliding it in the grooves at the side.

- Press and rotate the control lever on the stove (

) to



- Press the ignition button ( ) until the burner lights. If

the burner does not light after 10 seconds, put a match

to the edge of the burner.

- Adjust the flame to the dimensions of the recipient by

using the two flow positions: HIGH (

) or LOW ( ).

Do not use recipients with a diameter less than 10 cm

or over 24 cm.

k) TURNING OFF THE SIDE BURNER

(depending on the model)

Return the control lever ( ) to the OFF (O) position,

then close the valve on the gas bottle if the grill is not in

use.

To close the lid, slide it in its grooves, pulling it upwards

until it reaches the spindle, then tip it forwards.

l) REPLACING THE GAS CYLINDER

- Always work in a well ventilated area and never in the

presence of a flame, spark or heat source.

- Return the control knobs in the "off" position (O) then

close the cylinder valve.

- Remove the regulator, check that the sealing joint is in

good condition.

- Put the full cylinder in place, refit the regulator, taking

care not to apply stress to the hose. Check for gas

leaks.

m) OPERATION

       

handle components which may be very hot.

On first use, heat the barbecue with the hood closed and

burners in the high position ( ) for around 30 minutes

in order to get rid of the paint smell on new parts.

In normal operation, preheat the barbecue with the lid

closed for 15 to 20 minutes to bring the cooking grids up

Campingaz 3 Series RBS LX Plus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info